Quantcast
Jump to content

Recommended Posts

Posted

You could first try unhooking the battery for 10 mins and closing tighter the cluster connector female ends to make sure you have good contact. I think you might have some rubbed wires that are shorting, or a broken one or two ... down by the handlebars is where youre getting the rub and alongside the gas tank ...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Tinkeringreg
      Hi my name is Greg and I just acquired a free 2000 yamaha kodiac 400 4x4 with the ultramatic transmission that does not run. I plan to get it going and use it around my property

    • By kaidella
      Bought 4 wheeler for kids. Used to run and soon as it was put in gear it died. I have put new carburater, new plug and battery. The neutral light won't come on. I replaced the solenoid, then the positive battery cable and today put new relay assembly on. Still no neutral light. Not getting any juice and I don't know why.
    • By jhamrick75
      If anyone is having issues with the Mikuni VM24SS carb, I thought I would post what issues I had and how I resolved them.
      Acquired a 93 Bayou 220 that had sat for over 4 years.
      The carb was extremely corroded and pitted and full of leftover fuel.
      Cleaned carb and bowl and was able to get the engine to start.
      Within 30 seconds exhaust would heat up and start to glow red hot.
      Removed carb and recleaned everything, including a second overnight soak.
      Needless to say, after removing the carb for the 5th time and my frustration to the limit I
      realized that my attention had been to the carb body and not to the bowl.
      There is a small brass rod on the bottom of the carb that goes down into the float bowl but is seperated from the main section. I had cleaned that area very well....I had thought.
      ***The corrosion had sealed off the channel that runs from the main bowl section to the small tube section on the side of the float bowl. No amount of carb cleaner was going to get it to budge. So i took a small nail and started to scrape away the corrosion and was eventually able to dislodge enought of the corrosion that carb cleaner would flow through that channel. ***
      I thoroughly cleaned each side of the channel in the float bowl and reinstalled the carb and now the issue of it running lean is gone.
      On a second note the fuel mixture screw was a nightmare to remove as the threads had been corroded and wouldnt let the screw come out. I used a little cutting oil and worked the mixture screw in and out until I was able to push past the corroded threads and completely remove the needle. After a couple passes with a tap to clean the threads it is like new again.
      Hope this helps if you are having a lean running machine.
    • By Sportsman500guy
      I bought a 1996 Sportsman 500 4x4 about a month ago, and I love it. Unfortunately, I've been experiencing a few problems with the high-range gear. The first problem is that the gear selector will intermittently pop out of high and into neutral. This problem will sometimes occur when starting from a stop and sometimes will also occur while at cruising speed. The last time this happened I stopped and put it back into gear, however, as soon as I tried to throttle the machine would die. I turned it on again with no problems put it back into high and it died again. Once again I turned it on with no problems put it into low instead and it worked fine with no problem. I drove in low down the road slowly for a little and then shifted back into high with no issues. 
         I plan on working on it this weekend and would just like some opinions or feedback from anyone who may have experienced these problems before. I'm very mechanically inclined but im unsure of exactly where to start as this is the first Polaris ATV that I've owned. Any feedback is appreciated and thanks in advance  
    • By Admin
      Looking for Arctic Cat ATV VIN (Vehicle Identification Number) Number Decoders? Once you find your ATV VIN number off the tag on your Arctic Cat ATV, you can go to all kinds of websites that have VIN Decoders available. The best ones are backed by the Arctic Cat ATV manufacturer, however there are plenty of aftermarket Arctic Cat ATV VIN Decoder websites on the web. This topic will stay pinned and if you find any to add, please do it with a reply. 
      The following Arctic Cat ATV VIN Decoder websites are available where you can just enter your VIN number and it will shows you some of your ATV model details:
      CycleVin.com - Use Our Off-Road Vehicle Search to look up ATVs and more!
      KBB.com https://www.kbb.com/vehicle-history-report/ 
      CARFAX https://www.carfax.com
      autoDNA https://www.autodna.com
      VinAudit http://www.vinaudit.com/
      decodeTHIS https://www.decodethis.com
      VINCario https://vindecoder.eu/
      NICB Theft Check https://www.nicb.org/theft_and_fraud_awareness/vincheck 
×
×
  • Create New...