Quantcast
Jump to content

2003 Yamaha Wolverine - MPH Question

YamahaWolverine

By YamahaWolverine
in General ATV Discussion

 Share

Recommended Posts

YamahaWolverine Rookie

YamahaWolverine

Posted
  • Author
Posted
Hello and welcome !!

Is this bike full time 4WD?

Stock 23" tires?

Make sure the valves are adjusted in spec, nice clean carb & filter, clear muffler ...

I was thinking more of 45 - low 50s ...

What all should I have done? Diff fluid changed, valves adjusted, timing checked, Carb clean?

oxidized_black Grand Master

oxidized_black

Posted
Posted

i have heard guys say they will do 5?, but i think alot of conditions need to apply.

the bike is near 500lbs wet, add a 150 - 180lb rider, thats alot for a 350 to push fast especially in 4X4 ... not saying its not true ... if you want up to top speeds, check the compression, make sure valve are in sync, and carb is good and clear ...

i would say a step up in carb jets, a k&n filter or equivalent, and a aftermarket muffler would have you in high 50s ... i know the 350 motor is the same as the big bear except for the top end, i might be scared going over 50 on the bear, i havent clocked it yet, but i would say it goes maybe 40 - 45 ...

there is a governor on the throttle too, you can fiddle with that to see if the speed increases ...

oxidized_black Grand Master

oxidized_black

Posted
Posted

if the bike runs good as it sits now, i would dump seafoam every other or so tank to keep the carb clear ... yes, check/change your fluids for sure, timing and valves, a quick compression check can tell you if rings are worn or wearing ,,,

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • BuckBilly
      Where you like to ride and what riding does for you?
      By BuckBilly
      I like to ride in wooded and grassy areas. It takes my mind off the everyday routines and helps me deal with my father's cancer. Also gives me a reason to get involved with forums like this one.
    • Kaz
      1999 Yamaha Big Bear 350 4x4 no spark
      By Kaz
      Troubleshooting a no spark issue, was running OK, maybe a little rich, turned it off, now no spark. I've checked/ohmed out the main key switch, the start/stop switch, neutral switch, brake switch - all good. It will crank the starter, but no spark with the starter or when I try the pull start. I've checked all fuses and diodes. Swapped battery. New plug. New coil. Swapped in a used CDI - no help. Traced, removed, cleaned, reattached all grounds. Removed things like my winch from the circuits to be sure a bad relay or something was dragging it down. When testing voltages, the orange wire going from the CDI to the ignition coil shows no/very low voltage-shouldn't it have 12V on it? Sometimes I get a very weak, intermittent glow on my spark tester, but not enough to fire the plug. I've checked continuity on just about all wires in the harness. Checked/cleaned/lubed w dielectric grease- all connections, redid a few that looked old/dirty. I've checked the stator resistances, all good, but have a stator and rectifier ordered anyway, will arrive Sunday. I verified that the rectifier has a voltage output back to charge the battery while cranking - 10.5-11V, low, but expected while starter is engaged. What else can I check as part of troubleshooting? I have a Haines service manual, but the 1999 350 4x4 seems to be an odd model, there isn't an exact electrical diagram for it, but found one for another year that has all the same number of wires and same color wires, so I've referenced that. Any hints, tips or advice would be appreciated! Thanks!
    • P_syko
      Need help! 1987 Yamaha Moto 4 350
      By P_syko
      I’m brand new to 4 wheelers and just bought a 1987 Yamaha Moto 4 350. It has good compression and fuel, but no spark. I’ve looked high and low trying to find how to test all the components of the ignition system, but can’t find anything. This has a new CDI box on it, but I suspect it might be the stator. How do I test the stator on this? Any help would be greatly appreciated! 
    • DPDISXR4Ti
      2003 Kodiak Leaking fuel from drain hose at bottom of carb
      By DPDISXR4Ti
      I hadn't driven my Kodiak for a two months, and since it was low on fuel, the first thing I did was filled it up to maybe 7/8 full. Getting ready to start it, I rotated the fuel selector switch to "on" and within seconds I smelled and saw fuel dripping onto the floor. I quickly turned it off and the fuel gradually stopped - I can repeat this.
      The fuel is flowing from the hose that is connected to the bottom of the carb, and routes around to the left side toward the wheel well. Any idea what's going on here? It ran fine the last time I had it out.
      Thanks...
    • P_syko
      Hello all!
      By P_syko
      Hello all! I’m new to the 4 wheeler world, but not new to the mechanic world. I was a diesel mechanic for many years and last year got into jet skis. I just bought a 1987 Yamaha moto 4 350 and now learning the ins and outs of 2 stroke engines. Looking forward to learning all the things. 

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...