Quantcast
Jump to content

2005 Eiger 400 4x4 Auto-stops when throttle is pressed.

bigisland

By bigisland
in Suzuki ATV Forum

 Share

Recommended Posts

bigisland Newbie

bigisland

Posted
Posted (edited)

Hello, I have a 2005 Suzuki Eiger Quad runner. 400 4x4 Auto

Starts ok. But when I push on the throttle, it stalls. Maybe the carb needs adjusted?

There is some kind adjustment wheel that turns. I suppose this adjust fuel/air mix to carb. Either way I turn that, it still stalls when gas applied.

Our Suzuki dealer is no longer here, Honda will not work on it...:mad:

Edited by bigisland
Ajmboy Grand Master

Ajmboy

Posted
Posted

Stoopid question...but have you checked to make sure the fuel shut-off valve is on? The fuel petcock.

Another reason could be that the carb float is stuck down. If the quad sits, it can be a problem where the float pin oxidizes and sticks the movement of the float, essentially causing a fuel starvation scenario. :yes:

  • 2 weeks later...
Grodon Newbie

Grodon

Posted
Posted

Had the same problem with my 07. Twice. Both times it was something foreign finding its way into the carb. This last time, was a damned bug. Best guess it got in through the vent line found just in front of your left nut. Installing a screen on that line next time I have spare time.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • Rich1028
      I Crashed My Quad
      By Rich1028
      I Crashed My Quad
      Well the Way I Ride, some of you knew it was Inevitable.
      Below are Three Videos.
      First one is Slow Motion of How it Happens.
      Second one is Normal Speed, and what happens after the Accident.
      Third one Follows more of what happens after .

      I Was Riding By Myself. I was going through a Mud HOLE Either there was a log or a rock, or A Dip but just as I was almost through it, Machine, Rolled over on my right side, as soon as I contacted the ground, I Heard A SNAP! I got up, flipped the Quad back over. I had the wind knocked out of me.

      5 broken Ribs
      1 Punctured Lung
      1 Broken Collar Bone
      2023 Quad Riding Season is Over for ME!
       
       
       
    • Kaz
      1999 Yamaha Big Bear 350 4x4 no spark
      By Kaz
      Troubleshooting a no spark issue, was running OK, maybe a little rich, turned it off, now no spark. I've checked/ohmed out the main key switch, the start/stop switch, neutral switch, brake switch - all good. It will crank the starter, but no spark with the starter or when I try the pull start. I've checked all fuses and diodes. Swapped battery. New plug. New coil. Swapped in a used CDI - no help. Traced, removed, cleaned, reattached all grounds. Removed things like my winch from the circuits to be sure a bad relay or something was dragging it down. When testing voltages, the orange wire going from the CDI to the ignition coil shows no/very low voltage-shouldn't it have 12V on it? Sometimes I get a very weak, intermittent glow on my spark tester, but not enough to fire the plug. I've checked continuity on just about all wires in the harness. Checked/cleaned/lubed w dielectric grease- all connections, redid a few that looked old/dirty. I've checked the stator resistances, all good, but have a stator and rectifier ordered anyway, will arrive Sunday. I verified that the rectifier has a voltage output back to charge the battery while cranking - 10.5-11V, low, but expected while starter is engaged. What else can I check as part of troubleshooting? I have a Haines service manual, but the 1999 350 4x4 seems to be an odd model, there isn't an exact electrical diagram for it, but found one for another year that has all the same number of wires and same color wires, so I've referenced that. Any hints, tips or advice would be appreciated! Thanks!
    • Travis_Smith
      KVF 400 Float Height
      By Travis_Smith
      I have a 2002 Kawasaki Prairie KVF 400 and im trying to figure out the actual float height... i have read 17mm +- 2mm, seen 13mm and 23mm... what is happening is it will start right up, rev a little and all is fine, when it warms and you put a load on it bogs down and sputters. no i don't have a manual
    • Mhatayas
      Oil leak 1985 suzuki 250
      By Mhatayas
      What should I do about this , bad oil leak where the filter cover bolts on . Can I use some gasket maker 

    • Dumass
      '03 Honda Sporttrax 400EX Carb issue.
      By Dumass
      My name says it all. I have a '03 Honda Sporttrax 400EX with a new aftermarket carb on it that seems to be having issues. I can start it but it idles really rough and when I give it throttle it just kills the engine. I have tried adjusting the idle screw but to no avail. I am in the San Diego Ca area. 
      Any advice will be greatly appreciated. I would also like to get an owners manual for the thing too but can't seem to find a downloadable one.

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...