Quantcast
Jump to content

Recommended Posts

Posted

Hi, I have just purchased a 2002 Yamaha Kodiak 400 I think, the vin has worn off and I have located an engine number I think it is J312E-004674, could anyone tell me where the engine number might be please

Posted

you will find a vin number STAMPED into the metal frame behind the front left tire (sitting on the bike), it is just behind the fender on the frame rail. you will need a good light and need to squint (LOL), to write it down. i dont think the engine # will give you alot of info ...

after you get the vin #, you can type it in here Yamaha VIN Decoder @ Motoverse.com

Capture-2_zps2325d071.jpg

Posted

Hi and thanks for the reply but the vin is completely gone from the area you pointed out, I have sanded it back lightly to take off the dirt and rust but it is completely gone, not sure what I can do now

Posted

Had a look there cant locate it so I took the piston to the dealer and they said its probably a 2002 model Thanks for your help tho.

Cheers

  • 6 years later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By kawasig
      Hello All
      I'm kinda new to ATVs. I just bought a 1987 Suzuki quad runner 230 Dual Range. I'm having a problem finding info on it. It's very clean, only 2.800 miles. The front wheels are only 30 in.center to center. I was thinking about adding wheel spacers to give it more stability. I realize the added stress on ball joints and bearings. I'm wondering if there are any other concerns? Any input is greatly appreciated!
    • By Kaz
      Troubleshooting a no spark issue, was running OK, maybe a little rich, turned it off, now no spark. I've checked/ohmed out the main key switch, the start/stop switch, neutral switch, brake switch - all good. It will crank the starter, but no spark with the starter or when I try the pull start. I've checked all fuses and diodes. Swapped battery. New plug. New coil. Swapped in a used CDI - no help. Traced, removed, cleaned, reattached all grounds. Removed things like my winch from the circuits to be sure a bad relay or something was dragging it down. When testing voltages, the orange wire going from the CDI to the ignition coil shows no/very low voltage-shouldn't it have 12V on it? Sometimes I get a very weak, intermittent glow on my spark tester, but not enough to fire the plug. I've checked continuity on just about all wires in the harness. Checked/cleaned/lubed w dielectric grease- all connections, redid a few that looked old/dirty. I've checked the stator resistances, all good, but have a stator and rectifier ordered anyway, will arrive Sunday. I verified that the rectifier has a voltage output back to charge the battery while cranking - 10.5-11V, low, but expected while starter is engaged. What else can I check as part of troubleshooting? I have a Haines service manual, but the 1999 350 4x4 seems to be an odd model, there isn't an exact electrical diagram for it, but found one for another year that has all the same number of wires and same color wires, so I've referenced that. Any hints, tips or advice would be appreciated! Thanks!
    • By Travis_Smith
      I have a 2002 Kawasaki Prairie KVF 400 and im trying to figure out the actual float height... i have read 17mm +- 2mm, seen 13mm and 23mm... what is happening is it will start right up, rev a little and all is fine, when it warms and you put a load on it bogs down and sputters. no i don't have a manual
    • By fwsamm
      Im aware that this relay needs a positive (+) and a negative (-) to activate the other side. The blue wire is the neutral wire so when in neutral it gets ground. The green wire is from the parking break; when you pull the break in it gets ground (-). however one of those two needs to be neutral so that the positive from kill switch can go to the starter relay. The ground from the starter relay is from the start switch. Which one (neutral or parking break) should have a positive (+) voltage?
    • By KSIM
      View File CFMOTO C-Force 400 service manual
      C-Force 400
      Submitter KSIM Submitted 03/19/2025 Category CFMOTO ATV  
×
×
  • Create New...