Quantcast
Jump to content

1997 Suzuki King Quad - Axle/Rear End

preppypyro

By preppypyro
in Suzuki ATV Forum

 Share

Recommended Posts

preppypyro Apprentice

preppypyro

Posted
Posted

Hey guys and gals,

I aquired a 97 King Quad 300 from my dad, it has a few problems but seems to be an ok runner, so Im just trying to decide if its worth sinking a few dollars into or not.

The problems it has are an intermittent electrical problem which I have shorted out, one front axle is really screwed near the tire (shouldnt be a problem fixing that) and only one rear tire spins.

So my question is has any of you guys torn apart the rear end of these things? I had the quad lifte in the air, and the right hand side rear tire spins and there is a little resistance there (that is the one that works) but the left hand side spins really freely.

So Im not familiar with these quads and axles at all, does this just sound like a matter of throwing a new axle in the rear end? Does it sound like something more, and something in the diff let go? Rear axles easy to pull or no?

Ive checked out the diagram on cheapcycleparts, and to me it looks like there could be a lot that could go wrong inside. I plan on ripping the quad apart this winter and repairing the issues, but was hoping to get a little insight if anyone has had these rear ends apart.

Thanks.

preppypyro Apprentice

preppypyro

Posted
  • Author
Posted

Thanks for the reply.

Yes I have found a parts bike to get parts from. I was pondering getting a used front axle, but this guy wants 100 bucks each, and on ebay I can find them for slightly over that.

Regarding the back side not spinning though, Im not sure if its just the axle that a guy needs or what. I know the way to do it is rip it apart and look, and I will yet, just dont have time right now, so was hoping someone has had theirs apart before and tell me that yes, its basically an axle that is the only thing that can cause that symptom, or no it could be this gear etc. that will cost more then the quad is worth!

The wife and I are going to get either a couple of new can ams, king quads or maybe grizzlys in a year and a half, but was hoping to keep this one and my big bear going strong till then!

preppypyro Apprentice

preppypyro

Posted
  • Author
Posted

Ok lemme pick your brain then.. haha

Have you ever had to replace an axle, because the symptoms were that one day it plainly quit working? The joints all seem fine (used but fine), and one day it just quit turning. (from what my father told me)

Thats the part that has me a little... hesitant to just go and buy axles!

preppypyro Apprentice

preppypyro

Posted
  • Author
Posted

Thanks for the manuals, I think I downloaded them from you before and ill check again when I get home.

The quad has independent rear suspension and cv axles.

If it was a straight axle I would be a little more familiar with it, but till I rip this one apart I dont really know much!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • Tim Keiper
      2 problems with 2000 Timberwolf 4x4
      By Tim Keiper
      1st problem, Does anyone know where I can find a stock carb for my Timberwolf, I have tried two different aftermarket carbs and they both suck. The machine runs great until it gets good and warm, then it keeps stalling unless I feather the throttle. it will even stall while I'm trying to go from 1st to reverse or vise versa. I took it to a buddy of mine who is a bike mechanic for years, and he told me try to find a factory carb. When I look online from dealers it says "NOT AVAILABLE" anyone have any suggestions ?
       
      2nd, The small tab on the rear axle for towing is to short for even pulling my small yard trailer, I can't even turn a little bit and hit hits. I tried making an extension which worked great as far as length, but it bends the tab and then the extension drags the ground. I have an idea of what to do to fix it, but wanted to see if anyone else has had this problem and see how you solved it.
    • Thumpinhard25
      01 bear tracker stutter/ bog, electrical ??
      By Thumpinhard25
      First thanks for any help guys, new to the forums and it's gotten me this far. I bought a 2001 bear tracker 250 for my family to get around the dirt bikes races. It wasn't running right and had a high idle. Previous owner thought it was a carb problem, so he ordered a new Zoom carb and new intake boot, but it still had the same high idle. ( I believe he had the throttle cable adjusted wrong, because it idled fine when I put it back together) So I tore down and cleaned the stock carb, and it started up and idled fine, but needed to have the choke 1/2 out to run.  I swapped to the new zoom carb and had the same issue. Choke half out bike ran ok. I played with the needle and the pilot screw with no change. ( bike did seem to be running rich though, but didn't get better when I tightened pilot screw or raised meddle) I Took it to the races and once I started bouncing around in the cattle fields the quad started cutting out real bad. It would barely run.  Sometimes it would run with choke off, sometimes choke 1/2, sometime choke full. I cleaned carb again, checked float level, and boots, no change still wouldn't run. Then suddenly it started running ok again.  This makes me believe it's an electrical issue rather then carb. I know there's no air leak, it's been checked, both carbs are clean( I've swapped them out a couple times, it starts up immediately and usually idles fine. But then bogs down/ or stutters under throttle. I saw the post on the guy who disconnected his rectifier and reconnected and suddenly it started working again, which lead me to believe it may be electrical and not carb.  So any advice on what I should check? Any way to test the CDI or rectifier?  Once again, I appreciate your help.  
    • Mikey69
      How did you get into Quads?
      By Mikey69
      Heres my story. Kinda long. I guess I was a late bloomer when it comes to quads. I had never ridden a quad in my life. Rode Dirt Bikes as a kid growing up. Back in Oct of '06 I found a Mustang on craigslist. Took it for a test drive one morning before work. Fast car. 351 Cleveland. I had planned on meeting the guy again after work. For some strange reason thats still to this day beyond me, I stopped in Hillsboro MotoSports on the way home from work. I had 6 Grand on me. There was a left over '05 sitting by the front door. It was on sale for $4999. It was $5499 OTD. I didnt even look at anything else. I knew nothing about quads accept I thought it really looked coool and I had the money in my pocket to buy it. I was sitting on it when the salesman walked up and asked... "Can I help you?" Without hestitation I pulled 60 Ben Franklins outta my front pocket and said "I want this Quad. Load it up in my truck." It was just about dark by the time I drove away from the shop. BTW, I didnt bother to ask my ol lady if I could buy it. LOL. Anyway, I took it by the house and showed her. She was kinda stunned but not mad. We drove over to a friend of mines house and unloaded it. I took it to the field across the street from his house. HOLY CHIT!!!!! I was surprised by the power. I had it for about 2 weeks and took it to Sand Lake. I was there a few hours and rolled it on a banked turn at the top of the bowl right before you get to the one-ways. When it rolled, I flew off and landed on my belly. The quad came bouncing and landed on my back. For a month I couldnt even walk. I was scared of it. I considered trading it for a 250EX. Went back to the shop. The salesman said..."Dude!!! You dont want a 250EX!!! Trust me. Just get used to it" I still wasnt convinced. I put it on craigslist for $4000. Calls were coming in. I had a guy that wanted to come look at it that evening. I decided to take it for one last ride at Browns Camp before I sold it. I was still afraid of it. After about 5 minutes I started feeling comfortable on it again. I decided right then, I loved my Honda 450 and would learn how to ride it instead of selling it. That was late Nov of '06. Work was slow for a Painter in Oregon. My new job everyday? Going to Browns Camp and ridding my Quad. I bought my Girl Friend an '02 Blaster. I rode my 450 for 4-6 hours almost every single day for 3 months. And yes, I know my way around Browns Camp pretty well. LOL. In March I bought her an '06 TRX250EX (Thank God I didnt trade my 450 for one of those) LOL Since then, I have become totally addicted to quads. I love them. Couldnt imagine not owning at least one quad. Luckily I have two. My "07 was $6500 OTD in July of '07. Bought it for my Girlfriend. Traded in her 250 EX. A month later we broke up. So, I wound up with two Honda 450's.
       
    • Rich1028
      I Crashed My Quad
      By Rich1028
      I Crashed My Quad
      Well the Way I Ride, some of you knew it was Inevitable.
      Below are Three Videos.
      First one is Slow Motion of How it Happens.
      Second one is Normal Speed, and what happens after the Accident.
      Third one Follows more of what happens after .

      I Was Riding By Myself. I was going through a Mud HOLE Either there was a log or a rock, or A Dip but just as I was almost through it, Machine, Rolled over on my right side, as soon as I contacted the ground, I Heard A SNAP! I got up, flipped the Quad back over. I had the wind knocked out of me.

      5 broken Ribs
      1 Punctured Lung
      1 Broken Collar Bone
      2023 Quad Riding Season is Over for ME!
       
       
       
    • kawasig
      I just bought a rare beast!
      By kawasig
      Hello All
      I'm kinda new to ATVs. I just bought a 1987 Suzuki quad runner 230 Dual Range. I'm having a problem finding info on it. It's very clean, only 2.800 miles. The front wheels are only 30 in.center to center. I was thinking about adding wheel spacers to give it more stability. I realize the added stress on ball joints and bearings. I'm wondering if there are any other concerns? Any input is greatly appreciated!

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...