-
Similar Forum Topics
-
By Coyote251
I'm trying to help a buddy out with his bike (he's not really on the internet or familiar with these forums) and I'll admit that I am not super familiar with the transmission and clutches in these bikes. I owned a Brute a few years ago, but never had an issue like this that I had to troubleshoot.
So basically my buddy bought a group lot of 650's to build one good bike out of. He got it all put together and has it running but when he pushes on the throttle the clutch doesn't engage till the RPM's are quite high and even when its moving it doesn't really speed up, almost seems like its in "limp mode". He's tried 2 different transmissions so I don't think that's the problem.
Is there any adjustment on the clutch engagement? Anything else I can tell him to look at? Let me know if you need anymore information if you think you can help.
-
By carkivey3
i just picked this up. was told ran fine but overheating issues led to replacing head gasket and head. has not ran since. he is not a mechanic but helped someone else who he could not get back to finish job, got aggravated and put up for sale. i was thinking timing issues. i have 110-120psi on all 3 cylinders so i think valves are correct. dont know about distributor yet. however i have no spark. i have no power going to ignition coil. tried to follow white wire but gets lost in wire harness. does anyone have a wiring diagram? can anyone tell me what conditions have to be met before starting. motor turns over so i would think all safeties are met but you never know.
-
By jhamrick75
If anyone is having issues with the Mikuni VM24SS carb, I thought I would post what issues I had and how I resolved them.
Acquired a 93 Bayou 220 that had sat for over 4 years.
The carb was extremely corroded and pitted and full of leftover fuel.
Cleaned carb and bowl and was able to get the engine to start.
Within 30 seconds exhaust would heat up and start to glow red hot.
Removed carb and recleaned everything, including a second overnight soak.
Needless to say, after removing the carb for the 5th time and my frustration to the limit I
realized that my attention had been to the carb body and not to the bowl.
There is a small brass rod on the bottom of the carb that goes down into the float bowl but is seperated from the main section. I had cleaned that area very well....I had thought.
***The corrosion had sealed off the channel that runs from the main bowl section to the small tube section on the side of the float bowl. No amount of carb cleaner was going to get it to budge. So i took a small nail and started to scrape away the corrosion and was eventually able to dislodge enought of the corrosion that carb cleaner would flow through that channel. ***
I thoroughly cleaned each side of the channel in the float bowl and reinstalled the carb and now the issue of it running lean is gone.
On a second note the fuel mixture screw was a nightmare to remove as the threads had been corroded and wouldnt let the screw come out. I used a little cutting oil and worked the mixture screw in and out until I was able to push past the corroded threads and completely remove the needle. After a couple passes with a tap to clean the threads it is like new again.
Hope this helps if you are having a lean running machine.
-
By Coyote251
View File 2016 Can-Am Outlander 570, 650 & 850 L-Series service manual
service manual - 2016 Can-Am Outlander L-Series
2016 Can-Am Outlander 570, 650 & 850 Standard Series Here is combined the base manual along with all the needed updates and the 2016 supplement manual into one manual
Submitter Coyote251 Submitted 01/03/2025 Category Can-Am BRP ATV
-
-
By Does_This_Look_Bent?
Hey everyone, I just replaced the carp on my 98 Kodiak 400 with PN#4SH-14101-00-00. It starts and idles perfect, but once it’s good and warmed up, it bogs out at 3/4 throttle or more… it sounds like it’s bouncing off a rev limiter haha… I tried the air fuel screw, all the way in and out 2-1/2, and it made it a touch better… tried 2 turns and no different. Am I missing something?
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.