Quantcast
Jump to content

Recommended Posts

Posted

I have a 2004 eigar 400 4x4. I am having trouble finding out why the battery will not stay charged. I have tried two new battery's. I can charge the battery and the quad will start but after it has ran for a while the battery goes dead. hit the starter and all it will do is cleck. while it is running with low battery you turn on the lights and it kill's the motor.

any ideas, I would love to get it running.

Posted

I'd say a bad stator or bad connection coming from the stator. Fire it up & see what the voltage reading is @ the battery, should be around 14.4 volts. Next check voltage output @ the stator connector with the engine running. Doing a continuity test on the stator wold be a good idea as well, with the engine off.

Posted

Checking all the connections would be a good idea, BUT....if you've boiled out a few batteries I'd definately be looking @ the regulator. It sounds like it's overcharging. Checking the out-put voltage @ the stator and @ the battery would help to figure it out. Looking past what you where "told", without checking it you are just taking stabs into the dark. Boiling out batteries tells me it is ovvercharging by quite a bit!! ( some stators output as much as 36v, that's WAY too much for a 12v system!)

  • 1 month later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Tim Keiper
      1st problem, Does anyone know where I can find a stock carb for my Timberwolf, I have tried two different aftermarket carbs and they both suck. The machine runs great until it gets good and warm, then it keeps stalling unless I feather the throttle. it will even stall while I'm trying to go from 1st to reverse or vise versa. I took it to a buddy of mine who is a bike mechanic for years, and he told me try to find a factory carb. When I look online from dealers it says "NOT AVAILABLE" anyone have any suggestions ?
       
      2nd, The small tab on the rear axle for towing is to short for even pulling my small yard trailer, I can't even turn a little bit and hit hits. I tried making an extension which worked great as far as length, but it bends the tab and then the extension drags the ground. I have an idea of what to do to fix it, but wanted to see if anyone else has had this problem and see how you solved it.
    • By Rich1028
      I Crashed My Quad
      Well the Way I Ride, some of you knew it was Inevitable.
      Below are Three Videos.
      First one is Slow Motion of How it Happens.
      Second one is Normal Speed, and what happens after the Accident.
      Third one Follows more of what happens after .

      I Was Riding By Myself. I was going through a Mud HOLE Either there was a log or a rock, or A Dip but just as I was almost through it, Machine, Rolled over on my right side, as soon as I contacted the ground, I Heard A SNAP! I got up, flipped the Quad back over. I had the wind knocked out of me.

      5 broken Ribs
      1 Punctured Lung
      1 Broken Collar Bone
      2023 Quad Riding Season is Over for ME!
       
       
       
    • By Tinkeringreg
      Hi my name is Greg and I just acquired a free 2000 yamaha kodiac 400 4x4 with the ultramatic transmission that does not run. I plan to get it going and use it around my property

    • By Kaz
      Troubleshooting a no spark issue, was running OK, maybe a little rich, turned it off, now no spark. I've checked/ohmed out the main key switch, the start/stop switch, neutral switch, brake switch - all good. It will crank the starter, but no spark with the starter or when I try the pull start. I've checked all fuses and diodes. Swapped battery. New plug. New coil. Swapped in a used CDI - no help. Traced, removed, cleaned, reattached all grounds. Removed things like my winch from the circuits to be sure a bad relay or something was dragging it down. When testing voltages, the orange wire going from the CDI to the ignition coil shows no/very low voltage-shouldn't it have 12V on it? Sometimes I get a very weak, intermittent glow on my spark tester, but not enough to fire the plug. I've checked continuity on just about all wires in the harness. Checked/cleaned/lubed w dielectric grease- all connections, redid a few that looked old/dirty. I've checked the stator resistances, all good, but have a stator and rectifier ordered anyway, will arrive Sunday. I verified that the rectifier has a voltage output back to charge the battery while cranking - 10.5-11V, low, but expected while starter is engaged. What else can I check as part of troubleshooting? I have a Haines service manual, but the 1999 350 4x4 seems to be an odd model, there isn't an exact electrical diagram for it, but found one for another year that has all the same number of wires and same color wires, so I've referenced that. Any hints, tips or advice would be appreciated! Thanks!
    • By Travis_Smith
      I have a 2002 Kawasaki Prairie KVF 400 and im trying to figure out the actual float height... i have read 17mm +- 2mm, seen 13mm and 23mm... what is happening is it will start right up, rev a little and all is fine, when it warms and you put a load on it bogs down and sputters. no i don't have a manual
×
×
  • Create New...