Quantcast
Jump to content

Recommended Posts

Posted

Forgive me if it's been asked before.

I have an 01 foreman 400

Being that it is full time 4X4 I thought its prob not a good idea to cruise around in the pavement too much. Shonuff the owners manual says DON'T!

I know once and a while it's ok like tomload the atv in the truck etc. But once and a while I'll take the kids down the block and back in the afternoon. How bad is this ??? Your thoughts.

  • 3 weeks later...
Posted

With full time 4WD it is similar to the back two tires being interconnected all of the time. When you turn the one wheel spins faster than the other so one tire has to spin on the pavement while the other one travels slower. You just have to be careful not to stress out the drive train with all time 4WD. The other tires spining faster will increase tire wear and be harder on the drive train but should not break anything. I plow in 4X4 on pavement all of the time.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By AnthonyT
      In search of my first ATV? What are good older 4x4 models?
    • By BuckBilly
      I like to ride in wooded and grassy areas. It takes my mind off the everyday routines and helps me deal with my father's cancer. Also gives me a reason to get involved with forums like this one.
    • By Kaz
      Troubleshooting a no spark issue, was running OK, maybe a little rich, turned it off, now no spark. I've checked/ohmed out the main key switch, the start/stop switch, neutral switch, brake switch - all good. It will crank the starter, but no spark with the starter or when I try the pull start. I've checked all fuses and diodes. Swapped battery. New plug. New coil. Swapped in a used CDI - no help. Traced, removed, cleaned, reattached all grounds. Removed things like my winch from the circuits to be sure a bad relay or something was dragging it down. When testing voltages, the orange wire going from the CDI to the ignition coil shows no/very low voltage-shouldn't it have 12V on it? Sometimes I get a very weak, intermittent glow on my spark tester, but not enough to fire the plug. I've checked continuity on just about all wires in the harness. Checked/cleaned/lubed w dielectric grease- all connections, redid a few that looked old/dirty. I've checked the stator resistances, all good, but have a stator and rectifier ordered anyway, will arrive Sunday. I verified that the rectifier has a voltage output back to charge the battery while cranking - 10.5-11V, low, but expected while starter is engaged. What else can I check as part of troubleshooting? I have a Haines service manual, but the 1999 350 4x4 seems to be an odd model, there isn't an exact electrical diagram for it, but found one for another year that has all the same number of wires and same color wires, so I've referenced that. Any hints, tips or advice would be appreciated! Thanks!
    • By Travis_Smith
      I have a 2002 Kawasaki Prairie KVF 400 and im trying to figure out the actual float height... i have read 17mm +- 2mm, seen 13mm and 23mm... what is happening is it will start right up, rev a little and all is fine, when it warms and you put a load on it bogs down and sputters. no i don't have a manual
    • By leecon
      WANTED MAIN CONTROL BOX/BRAINS for a 2014 Titan UTV Scout E2.
×
×
  • Create New...