Quantcast
Jump to content

Recommended Posts

Posted

hey guys, I have a 2004 400ex. I just installed a 426 big bore with new weisco piston/rings. The first start went good for about 10 seconds, it started right up with no hesitation, then it started blowing whitish blue smoke out the exhaust badly, after that it started blowing oil out of the exhaust. I think the o-ring at the bottom of the cylinder that sits around the sleeve ripped when installing. my engine also use to smoke a little when cold before the big bore kit then stop after warm, which was due to my valve seals, i also believe the valves came a little loose but not bad. The bike runs great, starts great, full compression, no power loss. i will blow through my entire oil reserve in maybe 30 minutes, thats how bad its shooting the oil out the exhaust. What do you think the issue could be?

Posted

after first start I took it out to an open area and ran it for 15mins and got on it a little but not too bad, then shut it off and let it cool down.. then I started it again and ran for 30mins same thing.. by this time I ran out of oil. I used Rotella 15w40 for break in, not sure if that could cause any issues?

Posted

Yeah, I'm thinking a small part of the problem was how it was broke in. On my motor, I let it just sit for 15 minutes idling, then let it sit until it's stone cold. Then let it idle for 30 minutes, then cool down. Then 45 minutes idling, then cool down. Then beat the crap out of it LOL.

Posted

I have bought new rings, gasket set and valve seals.. just waiting for it to get a little warmer out to install them. Im hoping that those will fix this issue..

Posted

I haven't really ran into it overheating besides letting it idle for like 10 minutes without any movement, but I was definatly thinking of going the spal fan route for extra piece of mind.

Posted
yes can do tht also:yes:........ so hows ur ex goin mario:wink:

Waitin on the motor, cleaning up the frame and plastics, changing all the bearings, collecting 450r shocks and having em revalved, straightening rear axle again. Adding some cooling tricks too! Im hoping all is back together by end of march but now it doesnt look it

Sent from my SGH-T959V using Tapatalk

Posted
I haven't really ran into it overheating besides letting it idle for like 10 minutes without any movement, but I was definatly thinking of going the spal fan route for extra piece of mind.

I havent had the experience but of what Ive read so far its not so much of an overheating problem with the motor but alot of the time its the carb getting heatsoaked from the additional heat the motor puts out. A warm carb heats up incoming air and causes the bike to be down on power. Sometimes its confused with overheating. Whether its true or not im not sure but a heatsoaked carb was an absolute nono when I was dragracing back in the day. In between runs we would put bags of ice on the motor and put a box fan on top of that. How to solve this on the trail i havent figured out yet but I will. I have one solution which involves Co2. I need to figure this one out though.

So far my cooling tricks involve a fluidyne cooler, spal fan, scoops and maybe a Co2 or water setup. Nitrous is too expensive.

Sent from my SGH-T959V using Tapatalk

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By AnthonyT
      In search of my first ATV? What are good older 4x4 models?
    • By Frank Angerano
      So I decided to pick up a small trailer if I could get one for the right price.  I found this one for a few hundred bucks on Craig’s list.  It is  a galvanized trailer which is exactly what I was looking for. The wood was shot and needed some minor repairs which I could care less about as long as the chassis was good. 
      I striped it down and put a new deck on. I had some vinyl realtree graphics that I had laying around so I added them to the fenders which I think worked out well. Very happy with this little guy.  
      I'm having the iron workers at my jobmake me up a few lightweight side rails that will have a 22 degree bend in them to accommodate the tires that slightly hang over the edge and will incorporate some tie down points as well. 








    • By kawasig
      Hello All
      I'm kinda new to ATVs. I just bought a 1987 Suzuki quad runner 230 Dual Range. I'm having a problem finding info on it. It's very clean, only 2.800 miles. The front wheels are only 30 in.center to center. I was thinking about adding wheel spacers to give it more stability. I realize the added stress on ball joints and bearings. I'm wondering if there are any other concerns? Any input is greatly appreciated!
    • By Trent Finnessey
      I’ve got a 2000 400ex with a dg slip on muffler, it came with he stock muffler on it but the previous owner had the dg in a box so I put it on. I’ve been riding it for the past month and a half and every time I let off it backfires, and the other day the backfires got way louder, 2x louder! I’m concerned that I may hurt my motor? Why does is backfire??? Thanks
    • By Tinkeringreg
      Hi my name is Greg and I just acquired a free 2000 yamaha kodiac 400 4x4 with the ultramatic transmission that does not run. I plan to get it going and use it around my property

×
×
  • Create New...