Quantcast
Jump to content

Recommended Posts

Posted

Just purchased 1987 LT-4WD from the estate of a deceased neighbor. It started when I brought it home but dripped gas from carb overflow. I put in a carb kit and a new choke plunger. Starts and runs better, but it won't idle and after running for 2 - 3 minutes the gas starts dripping. I took it to local dealer and he didn't see anything that would cause it. He suggested as a remote possibility that the fuel pump could be over pumping. Any suggestions and comments are welcome

Posted

When you installed the carb kit, did it include new floats?? Even if you replaced the needle and seat, if the float doesn't float, then it will continue pushing fuel into the carb. An easy way to test them is to pull out the floats and drop them into a container of fuel to see if they are buoyant. If they aren't, replace the floats. If they are, you may need to adjust the arm controlling the needle and seat, or replace the needle and seat if it won't seal. Hope this helps.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By kawasig
      Hello All
      I'm kinda new to ATVs. I just bought a 1987 Suzuki quad runner 230 Dual Range. I'm having a problem finding info on it. It's very clean, only 2.800 miles. The front wheels are only 30 in.center to center. I was thinking about adding wheel spacers to give it more stability. I realize the added stress on ball joints and bearings. I'm wondering if there are any other concerns? Any input is greatly appreciated!
    • By Dumass
      My name says it all. I have a '03 Honda Sporttrax 400EX with a new aftermarket carb on it that seems to be having issues. I can start it but it idles really rough and when I give it throttle it just kills the engine. I have tried adjusting the idle screw but to no avail. I am in the San Diego Ca area. 
      Any advice will be greatly appreciated. I would also like to get an owners manual for the thing too but can't seem to find a downloadable one.
    • By Trent Finnessey
      So I’ve got a 2000 Honda 400ex absolutely love it!! I’ve had it for about a month, I ride with bruteforce 750’s, outlander 850’s and 1000 sxs’s and I was thinking of getting a trx450r carb and a full hmf exhaust. And probably doing the air box mod too, how much power would this give my 400? Just a little different or a big difference? Cuz if it’s not much of a different I’ll just stick with my dg slip on..... thanks!
    • By Arizona
      I recently bought a 87 TRX 250 not running of course, the owner had a brand new Key Switch on it.
      I think it is the wrong one or wrong wire colors as the colors dont match up with wiring diagram i downloaded for it. 
      anyone have a pic of their ign switch wires where they connect with the wire colors for that model? I ended up leaving the black/w stripe and
      green wire disconnected in order to hot wire it for other testing but would like to know as the colors dont match diagram. 


    • By P_syko
      I’m brand new to 4 wheelers and just bought a 1987 Yamaha Moto 4 350. It has good compression and fuel, but no spark. I’ve looked high and low trying to find how to test all the components of the ignition system, but can’t find anything. This has a new CDI box on it, but I suspect it might be the stator. How do I test the stator on this? Any help would be greatly appreciated! 
×
×
  • Create New...