Quantcast
Jump to content

Engine problems #2

getacanam

By getacanam
in General ATV Discussion

 Share

Recommended Posts

getacanam Rookie

getacanam

Posted
Posted

I am new to this site and am still learning to use it. Thanks to all who welcomed me, sorry i havent found out how to message back.

My raptor 350 sounds like crap. Sounds like its something in the bottom end. Checked the oil and it looks fine, no signs of metal. After having it rebuilt a couple of years ago i am wondering if its worth fixing. Anybody have any clues of about how much it would run to fix it if its in the bottom end? Low ballpark/high ballpark? I cant get it into a shop this week and somebody is interested in buying it for $800.

Was told the timming chain was getting badly worn and it would make noise, which it was. But it is gotten to be a loud clank, not really a tick or hard knock.

Thanks for any advise

hangingon Grand Master

hangingon

Posted
Posted

I hope I make this very easy for you to make your decisson on what to do. I know we posted part it out. Just go to ebay and price what Raptor parts are selling for some of the parts may shock you for what you could sell them for. You may be able to get more than 800.00. I have a utility and some parts are over a 1000.00 Raptors are big sellers. depending on what it would cost it might be worth fixing either way I would have it checked out before selling it.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • BuckBilly
      Where you like to ride and what riding does for you?
      By BuckBilly
      I like to ride in wooded and grassy areas. It takes my mind off the everyday routines and helps me deal with my father's cancer. Also gives me a reason to get involved with forums like this one.
    • ATVNetwork
      AMA Pro ATV Athletes Take Over Florida in Back-To-Back Events
      By ATVNetwork
      As the 2025 ATV Motocross National Championship Series (ATVMX), an AMA National Championship, got underway with back-to-back Florida AMA Pro only events, it was evident that Phoenix Racing Yamaha’s Joel Hetrick picked up where he left off last season.View the full article
    • Kaz
      1999 Yamaha Big Bear 350 4x4 no spark
      By Kaz
      Troubleshooting a no spark issue, was running OK, maybe a little rich, turned it off, now no spark. I've checked/ohmed out the main key switch, the start/stop switch, neutral switch, brake switch - all good. It will crank the starter, but no spark with the starter or when I try the pull start. I've checked all fuses and diodes. Swapped battery. New plug. New coil. Swapped in a used CDI - no help. Traced, removed, cleaned, reattached all grounds. Removed things like my winch from the circuits to be sure a bad relay or something was dragging it down. When testing voltages, the orange wire going from the CDI to the ignition coil shows no/very low voltage-shouldn't it have 12V on it? Sometimes I get a very weak, intermittent glow on my spark tester, but not enough to fire the plug. I've checked continuity on just about all wires in the harness. Checked/cleaned/lubed w dielectric grease- all connections, redid a few that looked old/dirty. I've checked the stator resistances, all good, but have a stator and rectifier ordered anyway, will arrive Sunday. I verified that the rectifier has a voltage output back to charge the battery while cranking - 10.5-11V, low, but expected while starter is engaged. What else can I check as part of troubleshooting? I have a Haines service manual, but the 1999 350 4x4 seems to be an odd model, there isn't an exact electrical diagram for it, but found one for another year that has all the same number of wires and same color wires, so I've referenced that. Any hints, tips or advice would be appreciated! Thanks!
    • Mhatayas
      Oil leak 1985 suzuki 250
      By Mhatayas
      What should I do about this , bad oil leak where the filter cover bolts on . Can I use some gasket maker 

    • P_syko
      Need help! 1987 Yamaha Moto 4 350
      By P_syko
      I’m brand new to 4 wheelers and just bought a 1987 Yamaha Moto 4 350. It has good compression and fuel, but no spark. I’ve looked high and low trying to find how to test all the components of the ignition system, but can’t find anything. This has a new CDI box on it, but I suspect it might be the stator. How do I test the stator on this? Any help would be greatly appreciated! 

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...