Quantcast
Jump to content

Warrior 2000 no start

JAVUTV

By JAVUTV
in Yamaha ATV Forum

 Share

Recommended Posts

JAVUTV Apprentice

JAVUTV

Posted
Posted (edited)

Hello¡ i need help my warrior dont start

somebody tell me the specs to stator

it has spark but dont start either pop nothing

I CHECK TIMMING AND APPEAR BOFORE T I DONT KNOW IF ITS CORRECT OR NOT

COMPRESSION 150PSI ....now i have checked the resistance in 4 wires in the stator RED & WITHE=219 OHMS AND THE OTHERS 2 WIRES GREEN STRIPED YELLOW=1195 AND YOU HAVE REASON DIRTDEMON IT HAS A PISTON J.E OK I DON'T HAVE THE SPECS THEN WHAT I DO??

HELP ME¡¡¡

Edited by JAVUTV
MORE INFORMATION
DirtDemon Veteran

DirtDemon

Posted
Posted

What do you mean, you checked the timing and it appears before T? If the machine sparks way before TDC, then you probably have a sheared flywheel key. Another thing to check is the vavle lash. BTW, 150psi is pretty strong for a Warrior, you might even have a high comp piston or a slightly shaved head. Make sure you are using premium unleaded fuel.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • Tinkeringreg
      Kodiac no start project
      By Tinkeringreg
      Hi my name is Greg and I just acquired a free 2000 yamaha kodiac 400 4x4 with the ultramatic transmission that does not run. I plan to get it going and use it around my property

    • Kaz
      1999 Yamaha Big Bear 350 4x4 no spark
      By Kaz
      Troubleshooting a no spark issue, was running OK, maybe a little rich, turned it off, now no spark. I've checked/ohmed out the main key switch, the start/stop switch, neutral switch, brake switch - all good. It will crank the starter, but no spark with the starter or when I try the pull start. I've checked all fuses and diodes. Swapped battery. New plug. New coil. Swapped in a used CDI - no help. Traced, removed, cleaned, reattached all grounds. Removed things like my winch from the circuits to be sure a bad relay or something was dragging it down. When testing voltages, the orange wire going from the CDI to the ignition coil shows no/very low voltage-shouldn't it have 12V on it? Sometimes I get a very weak, intermittent glow on my spark tester, but not enough to fire the plug. I've checked continuity on just about all wires in the harness. Checked/cleaned/lubed w dielectric grease- all connections, redid a few that looked old/dirty. I've checked the stator resistances, all good, but have a stator and rectifier ordered anyway, will arrive Sunday. I verified that the rectifier has a voltage output back to charge the battery while cranking - 10.5-11V, low, but expected while starter is engaged. What else can I check as part of troubleshooting? I have a Haines service manual, but the 1999 350 4x4 seems to be an odd model, there isn't an exact electrical diagram for it, but found one for another year that has all the same number of wires and same color wires, so I've referenced that. Any hints, tips or advice would be appreciated! Thanks!
    • Kawasakibayounospark
      Kawasaki bayou 400 no spark
      By Kawasakibayounospark
      any one know much about how this system works. Replaced voltage regulator cid box coil pickup coil have power to cid box none out to coil any thoughts. This is cid box number three 
    • P_syko
      Need help! 1987 Yamaha Moto 4 350
      By P_syko
      I’m brand new to 4 wheelers and just bought a 1987 Yamaha Moto 4 350. It has good compression and fuel, but no spark. I’ve looked high and low trying to find how to test all the components of the ignition system, but can’t find anything. This has a new CDI box on it, but I suspect it might be the stator. How do I test the stator on this? Any help would be greatly appreciated! 
    • carkivey3
      2008 kazuma 800 4x4. i need wiring help. no spark
      By carkivey3
      i just picked this up. was told ran fine but overheating issues led to replacing head gasket and head. has not ran since. he is not a mechanic but helped someone else who he could not get back to finish job, got aggravated and put up for sale. i was thinking timing issues. i have 110-120psi on all 3 cylinders so i think valves are correct. dont know about distributor yet. however i have no spark. i have no power going to ignition coil. tried to follow white wire but gets lost in wire harness. does anyone have a wiring diagram? can anyone tell me what conditions have to be met before starting. motor turns over so i would think all safeties are met but you never know.

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...