Quantcast
Jump to content

Recommended Posts

Posted

The best intake for your bike is dependant on what type of conditions you ride in. If you ride around any water, you want to keep your airbox, if you are in conditions that are always dry, you can do away with it, but you filter will need cleaning much more frequently. If you go with a fabric type filter like a K&N, use a pre-filter, and always check it for tears. Also, keep it clean and oiled. These filters are tops for flow and power increase IMO, but they require maintinence to operate properly. Always follow the cleaning procedures to a T, and let the filter dry completely before applying the oil. Foam filters are less hassle, better for dusty conditions, but are not good in sand because they will load up and are more restrictive. Foam filters still need to be cleaned and oiled regularly, but not as often as a K&N type. That being said, you generally get what you pay for, so do some research and find what best suits your particular needs.

Posted

Thanks for the info I ride in a lot of diffrent weather condtions so it is proablly best if I keep the air bow but I think I want to stick with a foam filter type I have found one by Pro Design that I am looking into, again thanks for your input.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Coyote251
      I'm trying to help a buddy out with his bike (he's not really on the internet or familiar with these forums) and I'll admit that I am not super familiar with the transmission and clutches in these bikes. I owned a Brute a few years ago, but never had an issue like this that I had to troubleshoot.
      So basically my buddy bought a group lot of 650's to build one good bike out of. He got it all put together and has it running but when he pushes on the throttle the clutch doesn't engage till the RPM's are quite high and even when its moving it doesn't really speed up, almost seems like its in "limp mode". He's tried 2 different transmissions so I don't think that's the problem. 
      Is there any adjustment on the clutch engagement? Anything else I can tell him to look at? Let me know if you need anymore information if you think you can help.  
    • By Kawasakibayounospark
      any one know much about how this system works. Replaced voltage regulator cid box coil pickup coil have power to cid box none out to coil any thoughts. This is cid box number three 
    • By neilroy87
      I have a 1990 Bayou 220 that runs pretty well for it's age--needs a new muffler, but sounds tough.    Have had to start with a pull cord since I got it, and recently started troubleshooting the start button.  Finding a lot of information on this issue in the forum, but haven't been able to chase it down yet.  Got a new battery, new starter solenoid, and going to replace the starter relay this week, but not convinced that's going to do the trick, since I can't get the neutral light on when turning the key on.  I can start it by jumping the solenoid, but the 2 black wires to the relay do not activate the starter.  Bad ground or a short somewhere?  Is there a good way to just test the ground?
    • By carkivey3
      i just picked this up. was told ran fine but overheating issues led to replacing head gasket and head. has not ran since. he is not a mechanic but helped someone else who he could not get back to finish job, got aggravated and put up for sale. i was thinking timing issues. i have 110-120psi on all 3 cylinders so i think valves are correct. dont know about distributor yet. however i have no spark. i have no power going to ignition coil. tried to follow white wire but gets lost in wire harness. does anyone have a wiring diagram? can anyone tell me what conditions have to be met before starting. motor turns over so i would think all safeties are met but you never know.
    • By Ajmboy
      View File 1986-2006 Kawasaki Bayou 300 service manual
      This service manual is for a 1986-2006 Kawasaki Bayou 300.
      Adding to downloads library.
      Submitter Ajmboy Submitted 05/11/2018 Category Kawasaki ATV  
×
×
  • Create New...