Quantcast
Jump to content

Recommended Posts

Posted

whats up guys, need a little help here, the battery in my 96 honda fourtraxx 300 keeps draining. I disconnected the battery kickstarted it and tested power generated at battery terminals with motor only and was gettting 3.5 volts dc at idle and the quad ran fine with lights.

I then hooked battery up and checked started cylinoid for continuity with key on and off and had continuity both times, I also was able to start my quad by shorting terminals on starter cylinoid with key on and off as well.

I checked wires, connections and 2 fuses by battery and all checked out of, I assume its the starter cylinoide or is their things to check before buying parts--- thanks for your help

Posted

out of curiousity, are you suppose to be able to start the quad up by crossing the terminals on starter cylinoid even with the ignition in the off position, because mine starts starts up even with out the key in it

Posted

No, I don't think you should be able to start it without the key on. The key switch or the wires that run in/out of it are probably the issue. I would start by inspecting the wires for a dead short. If the wires look ok, then the problem is probably in the switch itself. Sounds like it is on even in the off position. I would take it apart and inpect it before replacing it. You may be able to fix it by cleaning it, could be some kind of metallic debris in the switch causing it to short.

Posted

I agree with DD. also check the wires at the switch for the 3.5 volts- there should be at least one hot there when OFF. that means the switch is likely screwed up. by the way, 3.5 volts is not enough to keep a 12 volt battery charged! Sounds like someone chased the problem around and then gave up on it. Could be a charging coil too. It's time to buy a manual with a wiring diagram in it. ebay city.... Keep at it, you'll find it.

PS: if you short across the starter terminals it should turn the starter over, but not start without the ignition switch set to run.

Posted

Hey man

i think you mean you were able to cranck your engine with the key on or off

that bike only works with conecting power, not grounding the cdi

you mention getting only 3.5 volts when engine running, no battery conected

your voltage regulator may be faulty

but to be sure, conect battery, check voltage on battery before you even turn the key on

now turn lights off and any other accesories you have off (have you??)

turn key on and kickstartit, when runing, check the battery voltage again, if its lower you have a battery voltage winner

just in case, disconect the three prung conector on the left side under the plastic corner that attaches to the gas tank, the one with 3 yellow wires, from the generator (stator), check continuity between them, it should be zero, also check each wire to ground, should be infinity, in this case voltage regulator is a winner

before u spend big bucks on regulator ask a friend whith same bike to trade regulators just to test, no harm will be done, no matter wich regulator you conect on what bike, i think all year models are the same, may be different on 92 or 95 models, but if conectors the same and wire color equal, no problemo, then make the same test on battery voltage, key off, then bike running, voltage should be allways higher

if your regulator proves good, then im affraid you need a new stator, i had that head exploding problem a few years back, when the stator checked ok and the regulator also, but by pulling the stator out, there was visible burns on one coil, so i had to re-wireit , too bad you are too far, i could rewire that stator myself for you

sorry for misspelling, keyboard has mind of itself

good luck

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Trent Finnessey
      I’ve got a 2000 400ex with a dg slip on muffler, it came with he stock muffler on it but the previous owner had the dg in a box so I put it on. I’ve been riding it for the past month and a half and every time I let off it backfires, and the other day the backfires got way louder, 2x louder! I’m concerned that I may hurt my motor? Why does is backfire??? Thanks
    • By Dumass
      My name says it all. I have a '03 Honda Sporttrax 400EX with a new aftermarket carb on it that seems to be having issues. I can start it but it idles really rough and when I give it throttle it just kills the engine. I have tried adjusting the idle screw but to no avail. I am in the San Diego Ca area. 
      Any advice will be greatly appreciated. I would also like to get an owners manual for the thing too but can't seem to find a downloadable one.
    • By Arizona
      I recently bought a 87 TRX 250 not running of course, the owner had a brand new Key Switch on it.
      I think it is the wrong one or wrong wire colors as the colors dont match up with wiring diagram i downloaded for it. 
      anyone have a pic of their ign switch wires where they connect with the wire colors for that model? I ended up leaving the black/w stripe and
      green wire disconnected in order to hot wire it for other testing but would like to know as the colors dont match diagram. 


    • By P_syko
      I’m brand new to 4 wheelers and just bought a 1987 Yamaha Moto 4 350. It has good compression and fuel, but no spark. I’ve looked high and low trying to find how to test all the components of the ignition system, but can’t find anything. This has a new CDI box on it, but I suspect it might be the stator. How do I test the stator on this? Any help would be greatly appreciated! 
    • By carkivey3
      i just picked this up. was told ran fine but overheating issues led to replacing head gasket and head. has not ran since. he is not a mechanic but helped someone else who he could not get back to finish job, got aggravated and put up for sale. i was thinking timing issues. i have 110-120psi on all 3 cylinders so i think valves are correct. dont know about distributor yet. however i have no spark. i have no power going to ignition coil. tried to follow white wire but gets lost in wire harness. does anyone have a wiring diagram? can anyone tell me what conditions have to be met before starting. motor turns over so i would think all safeties are met but you never know.
×
×
  • Create New...