Quantcast
Jump to content

Recommended Posts

Posted

Hi,

This weekend went on a trip with my all brand new cforce 1000 touring, went from tarmac to reach the small muddy places and dirt and even sand.

Was running great until tre situations occurred:

First, after putting 50km without problems and still respecting the break in on the engine, we came across a sand small uphill and just turned the 4x4, and almost reaching the top, got a strange loss of traction with a noise like something was slipping, the noise looked to came from the front but cannot give 100% sure it was the differential or not, but something was definitely slipping, also i disconnected the 4x4 and tried to make the uphill only rear traction and almost reaching the top the same noise. I got a friend that was on my old 850XC and it drove pass this small uphill almost at idle.....what do you think??? Belt Slipping, Front differential or Gearbox/CVT?

Second, after this situation, i had the engine light going from on to off on the trail back home, but on the trail back home, i had no issues with temp rising nor noises nor anything, we drove normally, but without sand nor uphills, just rolling normally on dirt roads.

Third, a strange situation, riding on normal mode, i was going at 38 to 40km rolling but the engine was revving on 4000rpm at those speeds, i feel that it was a little bit more reavs than usual for that speed, but this is my perception, what do you think on this???

 

 

Posted

If it was 20 years old i would say you could have something going on with the belt and shieve but this is brand new you should not have problems with anything. It is very possible that the dirt and sand you ran through may have affected the electronic lockup  to go into 4 wheel drive, but it shouldnt have. Im not that familiar with these very rarely work on new ones. I think i would contact the dealer.

  • Like 1
Posted (edited)
3 hours ago, Gwbarm said:

If it was 20 years old i would say you could have something going on with the belt and shieve but this is brand new you should not have problems with anything. It is very possible that the dirt and sand you ran through may have affected the electronic lockup  to go into 4 wheel drive, but it shouldnt have. Im not that familiar with these very rarely work on new ones. I think i would contact the dealer.

That is some truth yes, but i'm seeing some problems with brand new 1000 touring with slippering...and some if not almost changed Belt and Clutch...

But regarding the 4x4, it's strange since if we put on 4x4 on tarmac and dirt road no noises no nothing, only when is pushing this happens...

But, yes, we already contacted the dealer to see how things go.

Edited by nberga

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By AnthonyT
      In search of my first ATV? What are good older 4x4 models?
    • By Frank Angerano
      So I decided to pick up a small trailer if I could get one for the right price.  I found this one for a few hundred bucks on Craig’s list.  It is  a galvanized trailer which is exactly what I was looking for. The wood was shot and needed some minor repairs which I could care less about as long as the chassis was good. 
      I striped it down and put a new deck on. I had some vinyl realtree graphics that I had laying around so I added them to the fenders which I think worked out well. Very happy with this little guy.  
      I'm having the iron workers at my jobmake me up a few lightweight side rails that will have a 22 degree bend in them to accommodate the tires that slightly hang over the edge and will incorporate some tie down points as well. 








    • By jhamrick75
      If anyone is having issues with the Mikuni VM24SS carb, I thought I would post what issues I had and how I resolved them.
      Acquired a 93 Bayou 220 that had sat for over 4 years.
      The carb was extremely corroded and pitted and full of leftover fuel.
      Cleaned carb and bowl and was able to get the engine to start.
      Within 30 seconds exhaust would heat up and start to glow red hot.
      Removed carb and recleaned everything, including a second overnight soak.
      Needless to say, after removing the carb for the 5th time and my frustration to the limit I
      realized that my attention had been to the carb body and not to the bowl.
      There is a small brass rod on the bottom of the carb that goes down into the float bowl but is seperated from the main section. I had cleaned that area very well....I had thought.
      ***The corrosion had sealed off the channel that runs from the main bowl section to the small tube section on the side of the float bowl. No amount of carb cleaner was going to get it to budge. So i took a small nail and started to scrape away the corrosion and was eventually able to dislodge enought of the corrosion that carb cleaner would flow through that channel. ***
      I thoroughly cleaned each side of the channel in the float bowl and reinstalled the carb and now the issue of it running lean is gone.
      On a second note the fuel mixture screw was a nightmare to remove as the threads had been corroded and wouldnt let the screw come out. I used a little cutting oil and worked the mixture screw in and out until I was able to push past the corroded threads and completely remove the needle. After a couple passes with a tap to clean the threads it is like new again.
      Hope this helps if you are having a lean running machine.
    • By KSIM
      View File CFMOTO CFORCE 1000 CF1000AU/CF1000ATR service manual
      cforce_1000_2018.pdf
      Submitter KSIM Submitted 03/08/2025 Category CFMOTO ATV  
    • By KSIM
      View File CFMOTO CFORCE 520 CF500AU-7L/CF500AU-7S service manual
      CFMOTO CFORCE 520 CF500AU-7L/CF500AU-7S service manual
      Submitter KSIM Submitted 03/08/2025 Category CFMOTO ATV  
×
×
  • Create New...