Quantcast
Jump to content

2003 Yamaha Kodiak 400 Neutral Safety Switch

mans

By mans
in Yamaha ATV Forum

 Share

Recommended Posts

  • Admin changed the title to 2003 Yamaha Kodiak 400 Neutral Safety Switch
Mech Grand Master

Mech

Posted
Posted

A defective neutral light won't stop the power supply to the bike, it only stops the start system working, and, you can over-ride the start safety inhibit by pulling the left brake lever on I'm pretty sure.

Have you checked the fuse ? Do the lights or horn work ?

  • Like 1
fwsamm Newbie

fwsamm

Posted
Posted

The neutral wire usually connects to the switch on the left side of the engine. It’s usually under the shifter but this is automatic I believe. I’m still assuming it’s in the same place.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • Kaz
      1999 Yamaha Big Bear 350 4x4 no spark
      By Kaz
      Troubleshooting a no spark issue, was running OK, maybe a little rich, turned it off, now no spark. I've checked/ohmed out the main key switch, the start/stop switch, neutral switch, brake switch - all good. It will crank the starter, but no spark with the starter or when I try the pull start. I've checked all fuses and diodes. Swapped battery. New plug. New coil. Swapped in a used CDI - no help. Traced, removed, cleaned, reattached all grounds. Removed things like my winch from the circuits to be sure a bad relay or something was dragging it down. When testing voltages, the orange wire going from the CDI to the ignition coil shows no/very low voltage-shouldn't it have 12V on it? Sometimes I get a very weak, intermittent glow on my spark tester, but not enough to fire the plug. I've checked continuity on just about all wires in the harness. Checked/cleaned/lubed w dielectric grease- all connections, redid a few that looked old/dirty. I've checked the stator resistances, all good, but have a stator and rectifier ordered anyway, will arrive Sunday. I verified that the rectifier has a voltage output back to charge the battery while cranking - 10.5-11V, low, but expected while starter is engaged. What else can I check as part of troubleshooting? I have a Haines service manual, but the 1999 350 4x4 seems to be an odd model, there isn't an exact electrical diagram for it, but found one for another year that has all the same number of wires and same color wires, so I've referenced that. Any hints, tips or advice would be appreciated! Thanks!
    • Travis_Smith
      KVF 400 Float Height
      By Travis_Smith
      I have a 2002 Kawasaki Prairie KVF 400 and im trying to figure out the actual float height... i have read 17mm +- 2mm, seen 13mm and 23mm... what is happening is it will start right up, rev a little and all is fine, when it warms and you put a load on it bogs down and sputters. no i don't have a manual
    • KSIM
      CFMOTO C-Force 400 Service Manual
      By KSIM
      View File CFMOTO C-Force 400 service manual
      C-Force 400
      Submitter KSIM Submitted 03/19/2025 Category CFMOTO ATV  
    • Kawasakibayounospark
      Kawasaki bayou 400 no spark
      By Kawasakibayounospark
      any one know much about how this system works. Replaced voltage regulator cid box coil pickup coil have power to cid box none out to coil any thoughts. This is cid box number three 
    • DPDISXR4Ti
      2003 Kodiak Leaking fuel from drain hose at bottom of carb
      By DPDISXR4Ti
      I hadn't driven my Kodiak for a two months, and since it was low on fuel, the first thing I did was filled it up to maybe 7/8 full. Getting ready to start it, I rotated the fuel selector switch to "on" and within seconds I smelled and saw fuel dripping onto the floor. I quickly turned it off and the fuel gradually stopped - I can repeat this.
      The fuel is flowing from the hose that is connected to the bottom of the carb, and routes around to the left side toward the wheel well. Any idea what's going on here? It ran fine the last time I had it out.
      Thanks...

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...