Quantcast
Jump to content

Recommended Posts

Posted
hey guys does anyone no if u can make the reverse on a warrior 350 can go any faster. no matter how much gas u giv it, it doesnt go any faster it revs but no go!:aargh:

It must have a limiter on it, do you have a manual for the quad?

Posted
some rev boxes will disable the revlimiter on reverse. look around and you'll find it

but it does not make sense y i can rev it so high and not go. i mean i can spin the tire s at idle, so maybe jus very low gearing

Posted
hey guys does anyone no if u can make the reverse on a warrior 350 can go any faster. no matter how much gas u giv it, it doesnt go any faster it revs but no go!:aargh:

What year Warrior? How fast do you want to go? Are your tires spinning faster when you rev it?

Posted
why do u want to go so fast in reverse??? I actually hate the reverse lever on the warrior, i have so much friggin trouble sometimes gettin the thing outta reverse.

its so damn slow, i jus wanna go faster then stock, and wen ur stuck in mud it does me no good

Posted
why do u want to go so fast in reverse??? I actually hate the reverse lever on the warrior, i have so much friggin trouble sometimes gettin the thing outta reverse.

and yeah i hav trouble w gettin out sometimes 2, there all like that my buddies rappy 350 wouldnt disengage and it took like 5 min!:aargh:

Posted
and yeah i hav trouble w gettin out sometimes 2, there all like that my buddies rappy 350 wouldnt disengage and it took like 5 min!:aargh:

It seems to work better if your still moving and you put the lever back in gear from reverse. I dunno why. Also gotta play with the clutch alot to move it as well . :aargh:

Posted
It seems to work better if your still moving and you put the lever back in gear from reverse. I dunno why. Also gotta play with the clutch alot to move it as well . :aargh:

yeah ud think theyd hav fixxed it by now

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By BuckBilly
      I like to ride in wooded and grassy areas. It takes my mind off the everyday routines and helps me deal with my father's cancer. Also gives me a reason to get involved with forums like this one.
    • By Kaz
      Troubleshooting a no spark issue, was running OK, maybe a little rich, turned it off, now no spark. I've checked/ohmed out the main key switch, the start/stop switch, neutral switch, brake switch - all good. It will crank the starter, but no spark with the starter or when I try the pull start. I've checked all fuses and diodes. Swapped battery. New plug. New coil. Swapped in a used CDI - no help. Traced, removed, cleaned, reattached all grounds. Removed things like my winch from the circuits to be sure a bad relay or something was dragging it down. When testing voltages, the orange wire going from the CDI to the ignition coil shows no/very low voltage-shouldn't it have 12V on it? Sometimes I get a very weak, intermittent glow on my spark tester, but not enough to fire the plug. I've checked continuity on just about all wires in the harness. Checked/cleaned/lubed w dielectric grease- all connections, redid a few that looked old/dirty. I've checked the stator resistances, all good, but have a stator and rectifier ordered anyway, will arrive Sunday. I verified that the rectifier has a voltage output back to charge the battery while cranking - 10.5-11V, low, but expected while starter is engaged. What else can I check as part of troubleshooting? I have a Haines service manual, but the 1999 350 4x4 seems to be an odd model, there isn't an exact electrical diagram for it, but found one for another year that has all the same number of wires and same color wires, so I've referenced that. Any hints, tips or advice would be appreciated! Thanks!
    • By P_syko
      I’m brand new to 4 wheelers and just bought a 1987 Yamaha Moto 4 350. It has good compression and fuel, but no spark. I’ve looked high and low trying to find how to test all the components of the ignition system, but can’t find anything. This has a new CDI box on it, but I suspect it might be the stator. How do I test the stator on this? Any help would be greatly appreciated! 
    • By P_syko
      Does the 1987 moto 4 350 have a low oil sensor that kills spark? Or are these too old for that kind of thing? 
    • By bigd764
      Anyone know what this thing is ?





×
×
  • Create New...