-
Similar Forum Topics
-
By Coyote251
I'm trying to help a buddy out with his bike (he's not really on the internet or familiar with these forums) and I'll admit that I am not super familiar with the transmission and clutches in these bikes. I owned a Brute a few years ago, but never had an issue like this that I had to troubleshoot.
So basically my buddy bought a group lot of 650's to build one good bike out of. He got it all put together and has it running but when he pushes on the throttle the clutch doesn't engage till the RPM's are quite high and even when its moving it doesn't really speed up, almost seems like its in "limp mode". He's tried 2 different transmissions so I don't think that's the problem.
Is there any adjustment on the clutch engagement? Anything else I can tell him to look at? Let me know if you need anymore information if you think you can help.
-
By Kaz
Troubleshooting a no spark issue, was running OK, maybe a little rich, turned it off, now no spark. I've checked/ohmed out the main key switch, the start/stop switch, neutral switch, brake switch - all good. It will crank the starter, but no spark with the starter or when I try the pull start. I've checked all fuses and diodes. Swapped battery. New plug. New coil. Swapped in a used CDI - no help. Traced, removed, cleaned, reattached all grounds. Removed things like my winch from the circuits to be sure a bad relay or something was dragging it down. When testing voltages, the orange wire going from the CDI to the ignition coil shows no/very low voltage-shouldn't it have 12V on it? Sometimes I get a very weak, intermittent glow on my spark tester, but not enough to fire the plug. I've checked continuity on just about all wires in the harness. Checked/cleaned/lubed w dielectric grease- all connections, redid a few that looked old/dirty. I've checked the stator resistances, all good, but have a stator and rectifier ordered anyway, will arrive Sunday. I verified that the rectifier has a voltage output back to charge the battery while cranking - 10.5-11V, low, but expected while starter is engaged. What else can I check as part of troubleshooting? I have a Haines service manual, but the 1999 350 4x4 seems to be an odd model, there isn't an exact electrical diagram for it, but found one for another year that has all the same number of wires and same color wires, so I've referenced that. Any hints, tips or advice would be appreciated! Thanks!
-
By fwsamm
Im aware that this relay needs a positive (+) and a negative (-) to activate the other side. The blue wire is the neutral wire so when in neutral it gets ground. The green wire is from the parking break; when you pull the break in it gets ground (-). however one of those two needs to be neutral so that the positive from kill switch can go to the starter relay. The ground from the starter relay is from the start switch. Which one (neutral or parking break) should have a positive (+) voltage?
-
By P_syko
I’m brand new to 4 wheelers and just bought a 1987 Yamaha Moto 4 350. It has good compression and fuel, but no spark. I’ve looked high and low trying to find how to test all the components of the ignition system, but can’t find anything. This has a new CDI box on it, but I suspect it might be the stator. How do I test the stator on this? Any help would be greatly appreciated!
-
-
By carkivey3
i just picked this up. was told ran fine but overheating issues led to replacing head gasket and head. has not ran since. he is not a mechanic but helped someone else who he could not get back to finish job, got aggravated and put up for sale. i was thinking timing issues. i have 110-120psi on all 3 cylinders so i think valves are correct. dont know about distributor yet. however i have no spark. i have no power going to ignition coil. tried to follow white wire but gets lost in wire harness. does anyone have a wiring diagram? can anyone tell me what conditions have to be met before starting. motor turns over so i would think all safeties are met but you never know.
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.