Quantcast
Jump to content

Recommended Posts

Posted

As it should be easy to see I am not a four wheeler mechanic so I apologize for asking for help, I replaced my OEM carburetor with a aftermarket carburetor and with y’all’s help adjusted the air/ fuel and it ran great until this evening and I noticed a smell of fuel I inspected carburetor area and found a steady flow at the vent line on the bottom of the carburetor so my question is is the float the only thing that will cause this problem? Before I installed the carburetor I checked the jets for tightness and they all seemed fine?

Posted

The float could be stuck partly open or  misadjusted. about the only thing I can think of otherwise is if there is a drain valve on the floatbowl bottom it could be stuck open  by a bit of debris if you   pushed the button  to  let a little  fuel/  water out.

  • Like 1
Posted

It sounds like the float needle has got some dirt or fluff under it. The float needle's seat has an O ring to seal it to the carb body and those can leak too but it shouldn't be the case with a new carb that was ok to start with. Check the drain screw is done up first though if it has one, or check the drain valve if it has one as Dave is suggesting. I'm in New Zealand and I've never seen a drain button. I'd also turn the tap off and run the bowl empty, then turn the tap on and start tapping the carb body fairly hard around where the float needle is with a screwdriver handle.. It may just flush the dirt or wriggle the needle into a better position and it might come right. It works sometimes !

Sounds though like you might need to clean the fuel tank or tap filters or fit an after-market fuel filter.

  • Like 1
  • 2 weeks later...
  • 7 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By P_syko
      I’m brand new to 4 wheelers and just bought a 1987 Yamaha Moto 4 350. It has good compression and fuel, but no spark. I’ve looked high and low trying to find how to test all the components of the ignition system, but can’t find anything. This has a new CDI box on it, but I suspect it might be the stator. How do I test the stator on this? Any help would be greatly appreciated! 
    • By DPDISXR4Ti
      I hadn't driven my Kodiak for a two months, and since it was low on fuel, the first thing I did was filled it up to maybe 7/8 full. Getting ready to start it, I rotated the fuel selector switch to "on" and within seconds I smelled and saw fuel dripping onto the floor. I quickly turned it off and the fuel gradually stopped - I can repeat this.
      The fuel is flowing from the hose that is connected to the bottom of the carb, and routes around to the left side toward the wheel well. Any idea what's going on here? It ran fine the last time I had it out.
      Thanks...
    • By carkivey3
      i just picked this up. was told ran fine but overheating issues led to replacing head gasket and head. has not ran since. he is not a mechanic but helped someone else who he could not get back to finish job, got aggravated and put up for sale. i was thinking timing issues. i have 110-120psi on all 3 cylinders so i think valves are correct. dont know about distributor yet. however i have no spark. i have no power going to ignition coil. tried to follow white wire but gets lost in wire harness. does anyone have a wiring diagram? can anyone tell me what conditions have to be met before starting. motor turns over so i would think all safeties are met but you never know.
    • By mmikesell
      First post here need some help/advice. I bought a 2001 king quad 300, vin number JSAAK43A212111871. I have been trying to do some basic maintenance as it runs but doesn't idle all that well . I want to take out and clean/repair the  carb but when looking for parts it ask for model X Y K1 K2. How do I know which model I have? I have tried some vin decoders but they haven't told me. If anyone could recommend a carb rebuild kit for my quad Id appreciate it. Also any tips on tracking down an owners manual? 
    • By Dsluder
      I am having an issue with a hs500. I bought it broken and have been trying to get it running. It seems to be starving for fuel. If I put my hand over the intake it will crank but will not run for very long because I'm not able to get the correct airflow with my hand. The things I have done so far are. Replaced the fuel pump, fuel filter, mass airflow sensor, idle air adjuster, fuel injector, cleaned the throttle body, replaced the ecu, and still the same issue. I notice the injector does not spray when removed from the head. I dont know if that is common. 
       
      I am out of ideas on what to do next. I have removed the fuel line from the injector and it is getting plenty of fuel. If anyone has an idea on what could possibly be the issue I would be happy to try anything at this point.
×
×
  • Create New...