Quantcast
Jump to content

Recommended Posts

  • Ajmboy changed the title to 2008 Polaris Outlaw 525 high idle and stall
Posted

It sounds like it's going too lean..  Have you checked the fuel flow to the carb is adequate ? The best way is to turn the fuel tap off, then undo the carb drain screw and watch it flow out, then turn the fuel on and make sure it keeps flowing good. Then, with the engine warm, try adjusting the idle mixture. It should respond to a half turn either way, if it doesn't respond to a half turn in each direction(too lean and too rich), then there's a problem in the carb..

Another thing that might cause it would be tight valve clearances..  Unlikely if it has shim adjusters though.

Oh.. Tank breather too.. check that too, though that normally takes a while to manifest..

Posted

It does sound like it's running out of gas, but no spitting or sputtering it just dies. It sounds like it's idling at about 3000 rpm. I generally run mine carbs dry if I am not going to use it for a while and they don't sound like that, they slow down and then speed up before they die.

Posted

Good point Gw..  That is mostly the more common scenerio.. 

Thinking thinking...

I can't her that video.. bad internet..

So it's just running high steady revs is it, then suddenly cuts out ?

Carby breather hose blocked ?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By kawasig
      Hello All
      I'm kinda new to ATVs. I just bought a 1987 Suzuki quad runner 230 Dual Range. I'm having a problem finding info on it. It's very clean, only 2.800 miles. The front wheels are only 30 in.center to center. I was thinking about adding wheel spacers to give it more stability. I realize the added stress on ball joints and bearings. I'm wondering if there are any other concerns? Any input is greatly appreciated!
    • By Dumass
      My name says it all. I have a '03 Honda Sporttrax 400EX with a new aftermarket carb on it that seems to be having issues. I can start it but it idles really rough and when I give it throttle it just kills the engine. I have tried adjusting the idle screw but to no avail. I am in the San Diego Ca area. 
      Any advice will be greatly appreciated. I would also like to get an owners manual for the thing too but can't seem to find a downloadable one.
    • By Trent Finnessey
      So I’ve got a 2000 Honda 400ex absolutely love it!! I’ve had it for about a month, I ride with bruteforce 750’s, outlander 850’s and 1000 sxs’s and I was thinking of getting a trx450r carb and a full hmf exhaust. And probably doing the air box mod too, how much power would this give my 400? Just a little different or a big difference? Cuz if it’s not much of a different I’ll just stick with my dg slip on..... thanks!
    • By neilroy87
      I have a 1990 Bayou 220 that runs pretty well for it's age--needs a new muffler, but sounds tough.    Have had to start with a pull cord since I got it, and recently started troubleshooting the start button.  Finding a lot of information on this issue in the forum, but haven't been able to chase it down yet.  Got a new battery, new starter solenoid, and going to replace the starter relay this week, but not convinced that's going to do the trick, since I can't get the neutral light on when turning the key on.  I can start it by jumping the solenoid, but the 2 black wires to the relay do not activate the starter.  Bad ground or a short somewhere?  Is there a good way to just test the ground?
    • By DPDISXR4Ti
      I hadn't driven my Kodiak for a two months, and since it was low on fuel, the first thing I did was filled it up to maybe 7/8 full. Getting ready to start it, I rotated the fuel selector switch to "on" and within seconds I smelled and saw fuel dripping onto the floor. I quickly turned it off and the fuel gradually stopped - I can repeat this.
      The fuel is flowing from the hose that is connected to the bottom of the carb, and routes around to the left side toward the wheel well. Any idea what's going on here? It ran fine the last time I had it out.
      Thanks...
×
×
  • Create New...