Quantcast
Jump to content

Recommended Posts

Posted

My 300ex won't run unless hooked to jumper cables or to a battery charger. When I try to rev it up it gets quieter instead of louder, is the stator bad? Could a CDI cause this? Could something with the ignition cause this? The neutral light only comes on when hooked to a power source and goes off as soon as the power source is connected. After I disconnect it from a power source it'll run for a few minutes then die. It'll also pull start but pushing the gas nothing happens, the choke isn't on and the gas isn't on reserve. My friend thinks it may be a stator because after I charged the battery and went to ride it the other day the battery was drained again. Any help would be appreciated as I'm lost and don't know where to start

 

  • dominic_300ex changed the title to 2000 Honda Trx300ex won't run unless hooked to power source- Help needed
Posted

It sounds like a dead battery. If the battery was good and charged up, I'd expect it to run the bike for hours if there weren't too many electric starts or headlights.

You need to charge the battery with it disconnected from the bike, then turn the charger off and let it sit for an hour or four and then use a gauge to check it's voltage. It's voltage must be 12.6 or more. That checks the battery isn't self discharging. Then put it in the bike and before connecting the earth lead use the amps gauge to check for any discharge while the key's off. There shouldn't be more than about 2 milliamps. That checks the bike isn't draining the battery.

Then you connect the negative lead and start the engine and use the volt gauge on the battery to check the voltage is going up. It should go up to about 13.7 volts quite quickly and at an idle, and with a few revs and a few minutes it should get up to 14.7 volts. After a few minutes of running it should be somewhere between 13.7 and 14.7, and if you turn the headlights on it shouldn't drop below 13.7 as long as there are a few revs on. That all checks it's charging.  The last check is to turn the headlights off and hold the revs up watching the rising voltage and it mustn't go above 14.7 volts. That checks the regulator's working.

 

Posted

Would have to agree with mech. Most newer bikes have this same ole problem either low voltage from battery or battery dead .not old bikes Wich would fire up with jumpers and run all day if you didn't kill it. With all the lights and other newfangled electronic mess on bikes nowadays it's a wonder they run at all. I miss the old days. Good luck on bike. 

Posted
On 4/7/2023 at 2:40 PM, Mech said:

It sounds like a dead battery. If the battery was good and charged up, I'd expect it to run the bike for hours if there weren't too many electric starts or headlights.

You need to charge the battery with it disconnected from the bike, then turn the charger off and let it sit for an hour or four and then use a gauge to check it's voltage. It's voltage must be 12.6 or more. That checks the battery isn't self discharging. Then put it in the bike and before connecting the earth lead use the amps gauge to check for any discharge while the key's off. There shouldn't be more than about 2 milliamps. That checks the bike isn't draining the battery.

Then you connect the negative lead and start the engine and use the volt gauge on the battery to check the voltage is going up. It should go up to about 13.7 volts quite quickly and at an idle, and with a few revs and a few minutes it should get up to 14.7 volts. After a few minutes of running it should be somewhere between 13.7 and 14.7, and if you turn the headlights on it shouldn't drop below 13.7 as long as there are a few revs on. That all checks it's charging.  The last check is to turn the headlights off and hold the revs up watching the rising voltage and it mustn't go above 14.7 volts. That checks the regulator's working.

 

So right now the areas to check are the regular and stator?

Posted
On 4/7/2023 at 2:40 PM, Mech said:

It sounds like a dead battery. If the battery was good and charged up, I'd expect it to run the bike for hours if there weren't too many electric starts or headlights.

You need to charge the battery with it disconnected from the bike, then turn the charger off and let it sit for an hour or four and then use a gauge to check it's voltage. It's voltage must be 12.6 or more. That checks the battery isn't self discharging. Then put it in the bike and before connecting the earth lead use the amps gauge to check for any discharge while the key's off. There shouldn't be more than about 2 milliamps. That checks the bike isn't draining the battery.

Then you connect the negative lead and start the engine and use the volt gauge on the battery to check the voltage is going up. It should go up to about 13.7 volts quite quickly and at an idle, and with a few revs and a few minutes it should get up to 14.7 volts. After a few minutes of running it should be somewhere between 13.7 and 14.7, and if you turn the headlights on it shouldn't drop below 13.7 as long as there are a few revs on. That all checks it's charging.  The last check is to turn the headlights off and hold the revs up watching the rising voltage and it mustn't go above 14.7 volts. That checks the regulator's working.

 

So right now the areas to check are the regular and stator?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By TravisM
      2001 bayou 220 KLF220A
      Need some help putting a new ignition switch on this thing. I'm not finding homes for all the wires. I can hook up the white wire and brown wire, But the switch has a B/W and Solid Yellow wire i can't find a home for, and there aren't any more wires in the vicinity from the harness that match this, except one red wire with a double female end crimped on, and a few B/Y grounds. None of the wiring diagrams i've founder or have been given match.
      I'm also wondering if i have the wrong switch? some switches appear to have 4 wires and other just 2, the Brown wire and a White wire.
      I'm at a loss here. Thanks.
       
    • By jwh
      I am new to this site. Now down to business, I have been given a Kawasaki 220, tires are trashed and it has been setting for a long time. Do I need a battery in it to find neutral? I know there is a neutral switch and if I shift down(7 times????)   then up one using the neutral switch I should be in Neutral. As you see I am in a learning curve here ......coments welcome.
    • By mans
      Were is the neutral safety switch on 03' Kodiak 400 4x4 . How xan i check it to see if it's good for a no neutral light no power to machine. Ty
    • By Snick
      Bought the project a few weeks ago with weak and intermittent spark. I could smack the CDI box with a screwdriver and it would work fine for a few days. Now, the smack trick is not working and machine is running awful with the weak spark and will most often not fire enough to turn the engine over through combustion (cranks very good). I ordered the GY6 CDI to see if I can get it going again as these CDI boxes are way too expensive even used. battery is fully charged and charging very good.
       
      Wondering if anyone knows how the GY6 (6-pin AC) CDI would wire to this machine. Attached is the electrical diagram. My confusion is with the green and orange wires sharing the 2-pin connector and the Blk/Red wire that runs to the magneto solo. How would I get AC power to the CDI through pin 1 on the GY6 when the CDI has two wires to the pickup-myabe just try one (orange then green) at a time?
       
       
       


       
      ^PINOUT:
            5   6
            2   4
           1    3
    • By pastorjeep
      Ok guys, I am a glutton for punishment! I picked up this 01 2wd Rancher because the plastics looked good on the marketplace. It has been sitting in the guys back yard for 10 years. The original engine blew and they swapped in an electric shift 4x4 engine. 😒The engine is locked up and was full of water. The wiring is hacked where they tried to get it to run and the rear end needs new swingarm bearings where they left it laying on the ground in the woods for 10 years. Has anyone here ever did the engine swap? First thing is to straighten out the wiring and get the engine free to see if I can get it to crank over. I have swingarm bearings ordered and a new ignition switch. So hopefully I can at least roll it around soon. 🤣





×
×
  • Create New...