-
Similar Forum Topics
-
By Thumpinhard25
First thanks for any help guys, new to the forums and it's gotten me this far. I bought a 2001 bear tracker 250 for my family to get around the dirt bikes races. It wasn't running right and had a high idle. Previous owner thought it was a carb problem, so he ordered a new Zoom carb and new intake boot, but it still had the same high idle. ( I believe he had the throttle cable adjusted wrong, because it idled fine when I put it back together) So I tore down and cleaned the stock carb, and it started up and idled fine, but needed to have the choke 1/2 out to run. I swapped to the new zoom carb and had the same issue. Choke half out bike ran ok. I played with the needle and the pilot screw with no change. ( bike did seem to be running rich though, but didn't get better when I tightened pilot screw or raised meddle) I Took it to the races and once I started bouncing around in the cattle fields the quad started cutting out real bad. It would barely run. Sometimes it would run with choke off, sometimes choke 1/2, sometime choke full. I cleaned carb again, checked float level, and boots, no change still wouldn't run. Then suddenly it started running ok again. This makes me believe it's an electrical issue rather then carb. I know there's no air leak, it's been checked, both carbs are clean( I've swapped them out a couple times, it starts up immediately and usually idles fine. But then bogs down/ or stutters under throttle. I saw the post on the guy who disconnected his rectifier and reconnected and suddenly it started working again, which lead me to believe it may be electrical and not carb. So any advice on what I should check? Any way to test the CDI or rectifier? Once again, I appreciate your help.
-
By Kaz
Troubleshooting a no spark issue, was running OK, maybe a little rich, turned it off, now no spark. I've checked/ohmed out the main key switch, the start/stop switch, neutral switch, brake switch - all good. It will crank the starter, but no spark with the starter or when I try the pull start. I've checked all fuses and diodes. Swapped battery. New plug. New coil. Swapped in a used CDI - no help. Traced, removed, cleaned, reattached all grounds. Removed things like my winch from the circuits to be sure a bad relay or something was dragging it down. When testing voltages, the orange wire going from the CDI to the ignition coil shows no/very low voltage-shouldn't it have 12V on it? Sometimes I get a very weak, intermittent glow on my spark tester, but not enough to fire the plug. I've checked continuity on just about all wires in the harness. Checked/cleaned/lubed w dielectric grease- all connections, redid a few that looked old/dirty. I've checked the stator resistances, all good, but have a stator and rectifier ordered anyway, will arrive Sunday. I verified that the rectifier has a voltage output back to charge the battery while cranking - 10.5-11V, low, but expected while starter is engaged. What else can I check as part of troubleshooting? I have a Haines service manual, but the 1999 350 4x4 seems to be an odd model, there isn't an exact electrical diagram for it, but found one for another year that has all the same number of wires and same color wires, so I've referenced that. Any hints, tips or advice would be appreciated! Thanks!
-
By fwsamm
Im aware that this relay needs a positive (+) and a negative (-) to activate the other side. The blue wire is the neutral wire so when in neutral it gets ground. The green wire is from the parking break; when you pull the break in it gets ground (-). however one of those two needs to be neutral so that the positive from kill switch can go to the starter relay. The ground from the starter relay is from the start switch. Which one (neutral or parking break) should have a positive (+) voltage?
-
By DPDISXR4Ti
I hadn't driven my Kodiak for a two months, and since it was low on fuel, the first thing I did was filled it up to maybe 7/8 full. Getting ready to start it, I rotated the fuel selector switch to "on" and within seconds I smelled and saw fuel dripping onto the floor. I quickly turned it off and the fuel gradually stopped - I can repeat this.
The fuel is flowing from the hose that is connected to the bottom of the carb, and routes around to the left side toward the wheel well. Any idea what's going on here? It ran fine the last time I had it out.
Thanks...
-
-
By beast6228
I've been trying to piece this Lakota 300 back together, slowly. It's been a rabbit hole however. I replace one thing, then it leads to replacing other things. Anyway, When I got this thing I noticed that the hose coming off the camshaft cover wasn't attached to anything, it was just hanging loose. (It's literally just a foot long hose attached to nothing) I figured since it was venting the head it would be ok and I am sure it is.
However, last night I was looking at the service manual and noticed that it mentioned that this atv has a crankcase breather tube as well. Mine does not have one, so I looked at Partzilla and looked at the parts diagram and sure enough, it's definitely supposed to have one. The problem however is, the service manual does not show how it hooks up and the parts diagram only shows the exploded view of the assembly. I just find that kind of strange, nowhere in the manual does it show how it connects. Does it have it connector, attach to a nipple? It just doesn't say and it bothers me that there is a hole there without anything attached to it. If anyone has a Bayou 300 or Lakota 300 with an intact breather vent system and could possibly take some clear photos of it or know how it connects I would be very grateful. I have searched high and low and cannot find any information on it.
Thanks
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.