Quantcast
Jump to content

Recommended Posts

Posted

i got this yamaha blaster. but i need to order some parts and i dont know what year it is or engine size. 2 or 4 stroke. every site i check for vin decoding doesnt give me an answer. can someone figure it out ? JY42XJW0XJ0015282  .The guy i bought it from said its a 2 stroke. but there isnt an oil reserve tank and there is an oil fill cap on the crankcase . unless thats a trans fill .

  • 4 weeks later...
Posted

It is a 2 stroke.

Yamaha Blaster Specs

  • Engine Type: 195cc, 2-Stroke Single cylinder, Air Cooled
  • Bore x Stroke: 66mm x 57mm
  • Compression Ratio: 6.6:1
  • Carb: Mikuni 26mm
  • Ignition: CDI
  • Yamaha Blaster Horsepower: 17HP
  • Starting System: Kickstart
  • Transmission: 6-Speed Manual Clutch
  • Drive Train: 2WD Sealed O-Ring Chain
  • Yamaha Blaster Top Speed: 55 MPH
  • Suspension/Front: Independent Double Wishbone, 7.1in. w/ 5-way Preload Adjustment
  • Suspension/Rear: Swing Arm, 7.1in. and Threaded Preload Adjustment
  • Brakes/Front: Dual Hydraulic Disc
  • Brakes/Rear: Hydraulic Disc
  • Tires/Front: AT21 x 7-10
  • Tires/Rear: AT21 x 10-8
  • L x W x H: 68.3in. x 40.7in. x 40.9in.
  • Yamaha Blaster Oil Capacity: 650ml (0.67 Quarts)
  • Wheelbase: 43.3in.
  • Yamaha Blaster Seat Height: 29.1 inches
  • Ground Clearance: 4.7in.
  • Fuel Capacity: 2.4 Gallons
  • Yamaha Blaster Weight: 324 Lbs.

Using the info below, yours was manufactured in Japan in 1998. 

Step 1

Locate the VIN on your Yamaha. The VIN is typically found below the handlebars and located on the steering stem. If you do not find the VIN on the steering stem, check the vehicle frame for a small metal plate that will display the VIN.

Step 2

Decode the meaning of your Yamaha motor vehicle VIN by breaking down the unique pattern of numbers and letters. For example, if the VIN starts with "4" or a "1" then your Yamaha was made in America, a "2" stands for Canada and "3" stands for Mexico. Vehicles made in Korea, Japan, England, Germany, Italy and Brazil would have vehicle identification numbers beginning with "K", "J", "S", "W", "Z" and "9", in that order. The secondary character of the VIN reflects the motor vehicle manufacturer, which would be a letter "C" for all Yamaha motor vehicles.

Step 3

Locate the third VIN digit. This stands for the manufacturer division that produced the motor vehicle.

Step 4

Notice VIN numbers four through eight. These 5 digits reflect the features found on the motor vehicle.

Step 5

Observe the ninth figure on the VIN. This particular digit is unique and used as security to guarantee a valid VIN number.

Step 6

Look at the 10th figure of the VIN. This stands for the year of the vehicle model. From the years 1988 to 2000, the tenth VIN figure would be "J" to "Y" and thereafter the 10th figure was changed to reflect a number.

Decode the last seven figures of the VIN following these rules: the 11th digit is the plant facility where the vehicle was assembled. Digits twelve through seventeen stand for the order that the vehicles were assembled.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Atomusthenes
      This topic is being opened to discuss the feasibility of forced induction on small engines.
    • By kawasig
      Hello All
      I'm kinda new to ATVs. I just bought a 1987 Suzuki quad runner 230 Dual Range. I'm having a problem finding info on it. It's very clean, only 2.800 miles. The front wheels are only 30 in.center to center. I was thinking about adding wheel spacers to give it more stability. I realize the added stress on ball joints and bearings. I'm wondering if there are any other concerns? Any input is greatly appreciated!
    • By Kaz
      Troubleshooting a no spark issue, was running OK, maybe a little rich, turned it off, now no spark. I've checked/ohmed out the main key switch, the start/stop switch, neutral switch, brake switch - all good. It will crank the starter, but no spark with the starter or when I try the pull start. I've checked all fuses and diodes. Swapped battery. New plug. New coil. Swapped in a used CDI - no help. Traced, removed, cleaned, reattached all grounds. Removed things like my winch from the circuits to be sure a bad relay or something was dragging it down. When testing voltages, the orange wire going from the CDI to the ignition coil shows no/very low voltage-shouldn't it have 12V on it? Sometimes I get a very weak, intermittent glow on my spark tester, but not enough to fire the plug. I've checked continuity on just about all wires in the harness. Checked/cleaned/lubed w dielectric grease- all connections, redid a few that looked old/dirty. I've checked the stator resistances, all good, but have a stator and rectifier ordered anyway, will arrive Sunday. I verified that the rectifier has a voltage output back to charge the battery while cranking - 10.5-11V, low, but expected while starter is engaged. What else can I check as part of troubleshooting? I have a Haines service manual, but the 1999 350 4x4 seems to be an odd model, there isn't an exact electrical diagram for it, but found one for another year that has all the same number of wires and same color wires, so I've referenced that. Any hints, tips or advice would be appreciated! Thanks!
    • By fwsamm
      Im aware that this relay needs a positive (+) and a negative (-) to activate the other side. The blue wire is the neutral wire so when in neutral it gets ground. The green wire is from the parking break; when you pull the break in it gets ground (-). however one of those two needs to be neutral so that the positive from kill switch can go to the starter relay. The ground from the starter relay is from the start switch. Which one (neutral or parking break) should have a positive (+) voltage?
    • By P_syko
      I’m brand new to 4 wheelers and just bought a 1987 Yamaha Moto 4 350. It has good compression and fuel, but no spark. I’ve looked high and low trying to find how to test all the components of the ignition system, but can’t find anything. This has a new CDI box on it, but I suspect it might be the stator. How do I test the stator on this? Any help would be greatly appreciated! 
×
×
  • Create New...