Quantcast
Jump to content

Recommended Posts

Posted

So I rebuilt this engine completely with all factory parts. Transmission was damaged, so customer wanted to replace crank while I had it apart. After putting everything back together, everything worked great. Customer picked up bike and ran it for about two months (he uses it daily for work in crawfish ponds). Brought it back to me because it was overheating and would rev up to about half throttle and the cut out over and over while holding the throttle at anything above half throttle. Radiator was plugged. Everything with ignition tests good. I never loose fire while this is happening. ECM is brand new, fuel pump is new, injector is new, swapped TP Sensor with known good one. Fuel pressure is at 51psi at idle and its hard to tell because of vibration, but seems to drop to about 42psi while its cutting in and out at high rev. Any ideas on what could cause this?

  • Ajmboy changed the title to 2007 Honda Rancher TRX420 4x4, Cuts out above half throttle similar to rev limiter
Posted

The dropping off of pressure at the same time it's missing , might be a dirty filter.. fuel filter. Even though the pressure's good at idle, it might not have a good flow. It always pays to check flow and pressure, because you can have one without the other.

Posted

So the fuel pump I replaced was aftermarket. I only replaced the pump itself and used original can. It came with new filter and seals. I'm not sure how the pressure regulator works on this system. It is only a spring valve. So what exactly tells the ECM when to cut the fuel pump on and off? Timing is set and valves are adjusted correctly. I guess the next step is to just replace the whole fuel pump canister. I will place the order for the new one and update once its installed. I am pretty certain that its a fuel pressure issue. Just not sure if its an electrical issue causing the pump to cut off when its throttled up or something else.

Posted

Are you sure it's not running in safe mode since the overheating issue ? Some of those things, if there's a problem that could damage the engine, they restrict the revs until you've fixed the problem, and in a lot of American stuff, taken the bike to a dealer to cancel the safe mode.

I suppose you have read the manual regarding this problem ..

  • 10 months later...
Posted

I completely forgot to give an update on this issue. It was the timing. It had jumped a tooth. I must have missed it when I had checked it the time before. I replaced the chain and tensioner. The bike has been in use for over a year now. The guy uses it daily for work. Thanks everyone for the help.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By ATVNetwork
      As the 2025 ATV Motocross National Championship Series (ATVMX), an AMA National Championship, got underway with back-to-back Florida AMA Pro only events, it was evident that Phoenix Racing Yamaha’s Joel Hetrick picked up where he left off last season.View the full article
    • By Arizona
      I recently bought a 87 TRX 250 not running of course, the owner had a brand new Key Switch on it.
      I think it is the wrong one or wrong wire colors as the colors dont match up with wiring diagram i downloaded for it. 
      anyone have a pic of their ign switch wires where they connect with the wire colors for that model? I ended up leaving the black/w stripe and
      green wire disconnected in order to hot wire it for other testing but would like to know as the colors dont match diagram. 


    • By leecon
      WANTED MAIN CONTROL BOX/BRAINS for a 2014 Titan UTV Scout E2.
    • By P_syko
      Hello all! I’m new to the 4 wheeler world, but not new to the mechanic world. I was a diesel mechanic for many years and last year got into jet skis. I just bought a 1987 Yamaha moto 4 350 and now learning the ins and outs of 2 stroke engines. Looking forward to learning all the things. 
    • By Ethan7387
      Hi could someone please help me, not to sure what engine this is 


×
×
  • Create New...