Quantcast
Jump to content

No spark 2017 Polaris 570

Jakelam

By Jakelam
in Polaris ATV Forum

 Share

Recommended Posts

Jakelam Rookie

Jakelam

Posted
Posted

no spark, I put a new plug in and still no spark...  I took a look at kill switch-jw if there is support to be bb in between the 2 metal spring loaded pieces?  And other suggestions?  I don’t know what the coil, plug wire, or cdi is supposed to ohm out at?? Repair manual?  Where is cdi located?? And is there supposed to be a green wire coming off of coil?  HELP!!!’

Jakelam Rookie

Jakelam

Posted
  • Author
Posted
On 8/10/2021 at 7:03 PM, Jakelam said:

I had the bike running perfectly fine, my buddy took it for a little ride. After he got back he hit the kill switch and forgot to turn the key off. We went to grab some food for about an hour. I went to start the wheeler up again and it didn’t start. I obviously switched the kill switch to run. It turns over but won’t go. I Pulled the spark plug out and threw a new one in, been in there since I bought it. Tried starting again and still got no spark. Where would I start troubleshooting this issue? 

 

Also, the fuel pump is not engaging...where do I start?

 

I pulled the chassis relay and get a clicking noise...also when that relay is in—you can feel it clicking—do you think it’s a bad relay?  Or could it be wiring somewhere?

colin james Community Regular

colin james

Posted
Posted

Feel pumps are common issue with these year machines. Check for power to the pump if it's ther remove cap and listen when key is turned on should hear pump prime if you hear gas drain back into tank pump is definitely bad

  • 6 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • BuckBilly
      Where you like to ride and what riding does for you?
      By BuckBilly
      I like to ride in wooded and grassy areas. It takes my mind off the everyday routines and helps me deal with my father's cancer. Also gives me a reason to get involved with forums like this one.
    • Kaz
      1999 Yamaha Big Bear 350 4x4 no spark
      By Kaz
      Troubleshooting a no spark issue, was running OK, maybe a little rich, turned it off, now no spark. I've checked/ohmed out the main key switch, the start/stop switch, neutral switch, brake switch - all good. It will crank the starter, but no spark with the starter or when I try the pull start. I've checked all fuses and diodes. Swapped battery. New plug. New coil. Swapped in a used CDI - no help. Traced, removed, cleaned, reattached all grounds. Removed things like my winch from the circuits to be sure a bad relay or something was dragging it down. When testing voltages, the orange wire going from the CDI to the ignition coil shows no/very low voltage-shouldn't it have 12V on it? Sometimes I get a very weak, intermittent glow on my spark tester, but not enough to fire the plug. I've checked continuity on just about all wires in the harness. Checked/cleaned/lubed w dielectric grease- all connections, redid a few that looked old/dirty. I've checked the stator resistances, all good, but have a stator and rectifier ordered anyway, will arrive Sunday. I verified that the rectifier has a voltage output back to charge the battery while cranking - 10.5-11V, low, but expected while starter is engaged. What else can I check as part of troubleshooting? I have a Haines service manual, but the 1999 350 4x4 seems to be an odd model, there isn't an exact electrical diagram for it, but found one for another year that has all the same number of wires and same color wires, so I've referenced that. Any hints, tips or advice would be appreciated! Thanks!
    • Kawasakibayounospark
      Kawasaki bayou 400 no spark
      By Kawasakibayounospark
      any one know much about how this system works. Replaced voltage regulator cid box coil pickup coil have power to cid box none out to coil any thoughts. This is cid box number three 
    • carkivey3
      2008 kazuma 800 4x4. i need wiring help. no spark
      By carkivey3
      i just picked this up. was told ran fine but overheating issues led to replacing head gasket and head. has not ran since. he is not a mechanic but helped someone else who he could not get back to finish job, got aggravated and put up for sale. i was thinking timing issues. i have 110-120psi on all 3 cylinders so i think valves are correct. dont know about distributor yet. however i have no spark. i have no power going to ignition coil. tried to follow white wire but gets lost in wire harness. does anyone have a wiring diagram? can anyone tell me what conditions have to be met before starting. motor turns over so i would think all safeties are met but you never know.
    • killerklown
      Kawasaki Bayou 220 Taillight Wire
      By killerklown
      What is the blue wire at taillight?

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...