-
Similar Forum Topics
-
By kawasig
Hello All
I'm kinda new to ATVs. I just bought a 1987 Suzuki quad runner 230 Dual Range. I'm having a problem finding info on it. It's very clean, only 2.800 miles. The front wheels are only 30 in.center to center. I was thinking about adding wheel spacers to give it more stability. I realize the added stress on ball joints and bearings. I'm wondering if there are any other concerns? Any input is greatly appreciated!
-
By jhamrick75
If anyone is having issues with the Mikuni VM24SS carb, I thought I would post what issues I had and how I resolved them.
Acquired a 93 Bayou 220 that had sat for over 4 years.
The carb was extremely corroded and pitted and full of leftover fuel.
Cleaned carb and bowl and was able to get the engine to start.
Within 30 seconds exhaust would heat up and start to glow red hot.
Removed carb and recleaned everything, including a second overnight soak.
Needless to say, after removing the carb for the 5th time and my frustration to the limit I
realized that my attention had been to the carb body and not to the bowl.
There is a small brass rod on the bottom of the carb that goes down into the float bowl but is seperated from the main section. I had cleaned that area very well....I had thought.
***The corrosion had sealed off the channel that runs from the main bowl section to the small tube section on the side of the float bowl. No amount of carb cleaner was going to get it to budge. So i took a small nail and started to scrape away the corrosion and was eventually able to dislodge enought of the corrosion that carb cleaner would flow through that channel. ***
I thoroughly cleaned each side of the channel in the float bowl and reinstalled the carb and now the issue of it running lean is gone.
On a second note the fuel mixture screw was a nightmare to remove as the threads had been corroded and wouldnt let the screw come out. I used a little cutting oil and worked the mixture screw in and out until I was able to push past the corroded threads and completely remove the needle. After a couple passes with a tap to clean the threads it is like new again.
Hope this helps if you are having a lean running machine.
-
By P_syko
Hello all! I’m new to the 4 wheeler world, but not new to the mechanic world. I was a diesel mechanic for many years and last year got into jet skis. I just bought a 1987 Yamaha moto 4 350 and now learning the ins and outs of 2 stroke engines. Looking forward to learning all the things.
-
By PIYIRIO
Hi all - I recently had a shop fix this quad and it hasn't been right since. The jug was resealed as it was leaking, the rings were replaced, and the valve stem seals replaced. Shop said the cylinder walls were great so nothing was done there. The motor still smokes, heavily on startup and all but quits once warmed up. Enough that I can live with it if I can fix what I came to ask about. I mentioned this work because since I've gotten it back it seems like it has power but tops out at a much slower speed than before. It's old so I don't have a speedo but I pulled out my phone at it tops out at 25 mph. I know before the work, I was getting up to 45+ mph... It's so bad, my 10 year old daughter is pulling away and straight leaving me in the dust with her governed Polaris 90.
Given the work done, what are some thing I could be the cause of such a drastic difference? I immediately thought timing but the marks appear to match up with a youtube video I found... no idea if it's correct though. It sat in another shop for 2 months and they gave me an $800 quote just for the starter... it pull starts fine.
FYI: I would take it back to the original shop to figure out but I had some issues that make them a no-go for me.
-
-
By dalton7545
ive had an account for years. cand dowload a manual tho havent posted enought so here is a post
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.