Quantcast
Jump to content

Recommended Posts

Posted

Hey there! New guy here! So I bought an 87 250. I turn the key and it has ignition light. I press run and the engine turns over. Guy I bought it from said the carbs may need cleaning, I worked them good cleaned and blown out. I reinstalled the carb and still doing the same thing. It’s getting fuel, the battery is brand new and charged I’m lost here!( purchased a new carb on its way) anyone have any ideas

04B4661B-D3B8-4E21-866D-093D0C406756.jpeg

Posted (edited)

After you turn it over a bit, does the plug get wet with fuel?  If there is fuel in the bowl and spark, then the issue could be timing is off (could be sparking at the wrong time), valves could be tight or loose, flywheel keyway could be sheared.

I'd start with checking timing to make sure it's spot on at TDC, then hit it with a touch of ether and see if it'll bust.  If it does, then it's a fuel delivery issue.  Have to go back into the carb and check the jets as there could be an obstruction.  If it doesn't at least try to bust on ether then i'd look at compression.  Could be that it has too little to run due to stuck or worn rings.

That thing is beautiful for an 87, what a find!

Edited by MarkinAR
  • 4 weeks later...
  • 1 year later...
  • 2 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By kawasig
      Hello All
      I'm kinda new to ATVs. I just bought a 1987 Suzuki quad runner 230 Dual Range. I'm having a problem finding info on it. It's very clean, only 2.800 miles. The front wheels are only 30 in.center to center. I was thinking about adding wheel spacers to give it more stability. I realize the added stress on ball joints and bearings. I'm wondering if there are any other concerns? Any input is greatly appreciated!
    • By ATVNetwork
      As the 2025 ATV Motocross National Championship Series (ATVMX), an AMA National Championship, got underway with back-to-back Florida AMA Pro only events, it was evident that Phoenix Racing Yamaha’s Joel Hetrick picked up where he left off last season.View the full article
    • By Mhatayas
      What should I do about this , bad oil leak where the filter cover bolts on . Can I use some gasket maker 

    • By P_syko
      I’m brand new to 4 wheelers and just bought a 1987 Yamaha Moto 4 350. It has good compression and fuel, but no spark. I’ve looked high and low trying to find how to test all the components of the ignition system, but can’t find anything. This has a new CDI box on it, but I suspect it might be the stator. How do I test the stator on this? Any help would be greatly appreciated! 
    • By carkivey3
      i just picked this up. was told ran fine but overheating issues led to replacing head gasket and head. has not ran since. he is not a mechanic but helped someone else who he could not get back to finish job, got aggravated and put up for sale. i was thinking timing issues. i have 110-120psi on all 3 cylinders so i think valves are correct. dont know about distributor yet. however i have no spark. i have no power going to ignition coil. tried to follow white wire but gets lost in wire harness. does anyone have a wiring diagram? can anyone tell me what conditions have to be met before starting. motor turns over so i would think all safeties are met but you never know.
×
×
  • Create New...