Quantcast
Jump to content

2003 Yamaha Bear Tracker 250 Carb Issue

K L Buck Naff

By K L Buck Naff
in Yamaha ATV Forum

 Share

Recommended Posts

K L Buck Naff Newbie

K L Buck Naff

Posted
Posted

Trying to replace the carburetor on my 2003 Bear Tracker 250. Two brand new carbs in a row from different suppliers.   Both leak fuel out over flow and intake as soon as I turn the gas on. Any ideas. Am I doing something wrong?

Randel1 Apprentice

Randel1

Posted
Posted

I have found that it is wise to pull the float bowl of any new or replacement carb. and examine the float level, jet size, needle and seat. Compare the jet sizes to assure they are the same as the original and make sure the float level is correct and the needle valve is not stuck.  Often times after market replacements lack the quality control standards of OEM parts.

Frank Angerano Grand Master

Frank Angerano

Posted
Posted

Carburetor cleaning / rebuild By Frank Angerano, August 6, 2019 in General ATV Discussion 
Original Content From:

@Randel1 hit on some very good points. Nothing like an oem carb. Aftermarket carburetors never work well unless they are a very aftermarket manufacturer and that price would compare to the oem carb price.   
 

Take a look at this post and maybe it will help you out. 

Keep in mind that your float needle has a rubber tip on it that closes off the fuel when the float rises. It gets worn. Could be as simple as that.   

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • ATVNetwork
      AMA Pro ATV Athletes Take Over Florida in Back-To-Back Events
      By ATVNetwork
      As the 2025 ATV Motocross National Championship Series (ATVMX), an AMA National Championship, got underway with back-to-back Florida AMA Pro only events, it was evident that Phoenix Racing Yamaha’s Joel Hetrick picked up where he left off last season.View the full article
    • Kaz
      1999 Yamaha Big Bear 350 4x4 no spark
      By Kaz
      Troubleshooting a no spark issue, was running OK, maybe a little rich, turned it off, now no spark. I've checked/ohmed out the main key switch, the start/stop switch, neutral switch, brake switch - all good. It will crank the starter, but no spark with the starter or when I try the pull start. I've checked all fuses and diodes. Swapped battery. New plug. New coil. Swapped in a used CDI - no help. Traced, removed, cleaned, reattached all grounds. Removed things like my winch from the circuits to be sure a bad relay or something was dragging it down. When testing voltages, the orange wire going from the CDI to the ignition coil shows no/very low voltage-shouldn't it have 12V on it? Sometimes I get a very weak, intermittent glow on my spark tester, but not enough to fire the plug. I've checked continuity on just about all wires in the harness. Checked/cleaned/lubed w dielectric grease- all connections, redid a few that looked old/dirty. I've checked the stator resistances, all good, but have a stator and rectifier ordered anyway, will arrive Sunday. I verified that the rectifier has a voltage output back to charge the battery while cranking - 10.5-11V, low, but expected while starter is engaged. What else can I check as part of troubleshooting? I have a Haines service manual, but the 1999 350 4x4 seems to be an odd model, there isn't an exact electrical diagram for it, but found one for another year that has all the same number of wires and same color wires, so I've referenced that. Any hints, tips or advice would be appreciated! Thanks!
    • Mhatayas
      Oil leak 1985 suzuki 250
      By Mhatayas
      What should I do about this , bad oil leak where the filter cover bolts on . Can I use some gasket maker 

    • fwsamm
      2001 Yamaha Bear Tracker Circuit Relay Issue
      By fwsamm
      Im aware that this relay needs a positive (+) and a negative (-) to activate the other side. The blue wire is the neutral wire so when in neutral it gets ground. The green wire is from the parking break; when you pull the break in it gets ground (-). however one of those two needs to be neutral so that the positive from kill switch can go to the starter relay. The ground from the starter relay is from the start switch. Which one (neutral or parking break) should have a positive (+) voltage?
    • DPDISXR4Ti
      2003 Kodiak Leaking fuel from drain hose at bottom of carb
      By DPDISXR4Ti
      I hadn't driven my Kodiak for a two months, and since it was low on fuel, the first thing I did was filled it up to maybe 7/8 full. Getting ready to start it, I rotated the fuel selector switch to "on" and within seconds I smelled and saw fuel dripping onto the floor. I quickly turned it off and the fuel gradually stopped - I can repeat this.
      The fuel is flowing from the hose that is connected to the bottom of the carb, and routes around to the left side toward the wheel well. Any idea what's going on here? It ran fine the last time I had it out.
      Thanks...

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...