Quantcast
Jump to content

Recommended Posts

Posted

Why would you have to convert to a stronger relay ? 
Is the existing one failing ?
A relay is pretty straight forward except for the manufacture brand, that’s where the quality is. Bosh makes a good relay and a few other brands. 

  • 2 weeks later...
Posted

I have3 of the stock fuel pump relays and my bikes fuel pump will not run with any of them.I used a better made relay and it would work for a little while and then it will go right back to not working.

Posted

My guess is that the power going to the relay is either not getting the proper voltage  to hold it closed.  Or it’s have a pulsing voltage that’s allowing the relay to not fully close.  

lastly I would check the ground and make sure it’s tight.  

Either condition will allow the contacts inside the relay to arc when they spot fully close and destroy the contacts hence a bad relay. 
So start by checkout voltages first and move on to grounds etc.   

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By Rich1028
      I Crashed My Quad
      Well the Way I Ride, some of you knew it was Inevitable.
      Below are Three Videos.
      First one is Slow Motion of How it Happens.
      Second one is Normal Speed, and what happens after the Accident.
      Third one Follows more of what happens after .

      I Was Riding By Myself. I was going through a Mud HOLE Either there was a log or a rock, or A Dip but just as I was almost through it, Machine, Rolled over on my right side, as soon as I contacted the ground, I Heard A SNAP! I got up, flipped the Quad back over. I had the wind knocked out of me.

      5 broken Ribs
      1 Punctured Lung
      1 Broken Collar Bone
      2023 Quad Riding Season is Over for ME!
       
       
       
    • By fwsamm
      Im aware that this relay needs a positive (+) and a negative (-) to activate the other side. The blue wire is the neutral wire so when in neutral it gets ground. The green wire is from the parking break; when you pull the break in it gets ground (-). however one of those two needs to be neutral so that the positive from kill switch can go to the starter relay. The ground from the starter relay is from the start switch. Which one (neutral or parking break) should have a positive (+) voltage?
    • By DPDISXR4Ti
      I hadn't driven my Kodiak for a two months, and since it was low on fuel, the first thing I did was filled it up to maybe 7/8 full. Getting ready to start it, I rotated the fuel selector switch to "on" and within seconds I smelled and saw fuel dripping onto the floor. I quickly turned it off and the fuel gradually stopped - I can repeat this.
      The fuel is flowing from the hose that is connected to the bottom of the carb, and routes around to the left side toward the wheel well. Any idea what's going on here? It ran fine the last time I had it out.
      Thanks...
    • By Ethan7387
      Hi could someone please help me, not to sure what engine this is 


    • By mmikesell
      First post here need some help/advice. I bought a 2001 king quad 300, vin number JSAAK43A212111871. I have been trying to do some basic maintenance as it runs but doesn't idle all that well . I want to take out and clean/repair the  carb but when looking for parts it ask for model X Y K1 K2. How do I know which model I have? I have tried some vin decoders but they haven't told me. If anyone could recommend a carb rebuild kit for my quad Id appreciate it. Also any tips on tracking down an owners manual? 
×
×
  • Create New...