Quantcast
Jump to content

2001 yamaha warrior YFM350x won't fire up

Chase Cook

By Chase Cook
in Yamaha ATV Forum

 Share

Recommended Posts

Chase Cook Enthusiast

Chase Cook

Posted
Posted

I have a Yamaha 350 in at once to try to fire up but won't. It's getting gas fire air and it has a lot of compression but still struggles to start check the timing it's top dead center valves are good valves are adjusted everything's working but won't fire I put my hand over the carb suck in gas and it tries to but it makes a lot of black smoke. Also when I put my hand over do you carb and tried to start it there's black black nasty stuff in the gas. So I don't know if it's trying to burn too much or what it is the gas tank clean and it anything to do with the gas it's with it firing. Took the spark plug out and it's pure black. What is dried up black not nasty corroded wet looking. Need help to solve the issue

Frank Angerano Grand Master

Frank Angerano

Posted
Posted

Welcome to Quadcrazy @Chase Cook  It sounds like a typical carburetor cleaning. Have you taken the carburetor off of the machine and broken it down to clean it ? 

Also have you looked into gas tank to make sure it’s clean and no rust and junk inside and the fuel valve is free flowing ? 

That would be my first move. Throw a fresh spark plug in as well and my guess is it will run fine.  

JacobSlabach Mentor

JacobSlabach

Posted
Posted

Yea start simple, smell gas in tank so make sure it's not diesel or have water in it.  Clean carb, black crap in gas sounds like gaskets in carb going bad or some other source of dry rotted rubber.

I'd replace gas lines and fuel filter, clean tank and carb with some carb cleaner, check carb gaskets, throw it back together with some fresh gas and fire it up!

  • Ajmboy changed the title to 2001 yamaha warrior YFM350x won't fire up

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Forum Topics

    • Tinkeringreg
      Kodiac no start project
      By Tinkeringreg
      Hi my name is Greg and I just acquired a free 2000 yamaha kodiac 400 4x4 with the ultramatic transmission that does not run. I plan to get it going and use it around my property

    • Kaz
      1999 Yamaha Big Bear 350 4x4 no spark
      By Kaz
      Troubleshooting a no spark issue, was running OK, maybe a little rich, turned it off, now no spark. I've checked/ohmed out the main key switch, the start/stop switch, neutral switch, brake switch - all good. It will crank the starter, but no spark with the starter or when I try the pull start. I've checked all fuses and diodes. Swapped battery. New plug. New coil. Swapped in a used CDI - no help. Traced, removed, cleaned, reattached all grounds. Removed things like my winch from the circuits to be sure a bad relay or something was dragging it down. When testing voltages, the orange wire going from the CDI to the ignition coil shows no/very low voltage-shouldn't it have 12V on it? Sometimes I get a very weak, intermittent glow on my spark tester, but not enough to fire the plug. I've checked continuity on just about all wires in the harness. Checked/cleaned/lubed w dielectric grease- all connections, redid a few that looked old/dirty. I've checked the stator resistances, all good, but have a stator and rectifier ordered anyway, will arrive Sunday. I verified that the rectifier has a voltage output back to charge the battery while cranking - 10.5-11V, low, but expected while starter is engaged. What else can I check as part of troubleshooting? I have a Haines service manual, but the 1999 350 4x4 seems to be an odd model, there isn't an exact electrical diagram for it, but found one for another year that has all the same number of wires and same color wires, so I've referenced that. Any hints, tips or advice would be appreciated! Thanks!
    • fwsamm
      2001 Yamaha Bear Tracker Circuit Relay Issue
      By fwsamm
      Im aware that this relay needs a positive (+) and a negative (-) to activate the other side. The blue wire is the neutral wire so when in neutral it gets ground. The green wire is from the parking break; when you pull the break in it gets ground (-). however one of those two needs to be neutral so that the positive from kill switch can go to the starter relay. The ground from the starter relay is from the start switch. Which one (neutral or parking break) should have a positive (+) voltage?
    • P_syko
      Need help! 1987 Yamaha Moto 4 350
      By P_syko
      I’m brand new to 4 wheelers and just bought a 1987 Yamaha Moto 4 350. It has good compression and fuel, but no spark. I’ve looked high and low trying to find how to test all the components of the ignition system, but can’t find anything. This has a new CDI box on it, but I suspect it might be the stator. How do I test the stator on this? Any help would be greatly appreciated! 
    • kaidella
      1995 Kawasaki bayou 220 won't start
      By kaidella
      Bought 4 wheeler for kids. Used to run and soon as it was put in gear it died. I have put new carburater, new plug and battery. The neutral light won't come on. I replaced the solenoid, then the positive battery cable and today put new relay assembly on. Still no neutral light. Not getting any juice and I don't know why.

COMMUNITY SECTIONS

ATV FORUMS

QUADCRAZY MEMBERSHIP

Be a part of best online community of ATV riders and join thousands of people who love ATVs! Share your ATV photos, videos, ATV rides, get help with your ATV and more. Not a member?

SIGN UP TODAY

ADVERTISE WITH US

FOLLOW US ON

  • Automotive Webmaster
×
×
  • Create New...