Quantcast
Jump to content

Recommended Posts

Posted

Hi all, new to the forum, looking forward to getting some help/advice on maintaining an 18 yr old atv!  So my King Quad 300, recently started running really rough (otherwise ok til this point) at anything more than idle.  After started, choke on/off, doesn't seem to matter, it shutters (Not sure how else to explain it) really bad when given throttle.  I can let the engine run for several minutes, but this never improves.  

Fuel pump checks out ok, and I don't see any gas in the fuel pump vacuum line.  I am a novice on a carburetor, but I need to see what's going on, so after taking it apart, I have a question about this plastic part with an o-ring that is above the jet needle.  Appears as if someone rebuilt this carb, because it is extremely clean...so I am wondering if this plastic part looks to be typical for this carb...or not.  Thanks in advance for the help!

20190309_142230.jpg

20190309_163338.jpg

20190309_141704.jpg

Posted

This is a thread I will follow with interest as I too have recently bought a King Quad 300 and it is in need of some attention due to rough running.  I will be stripping the carb out in due course and cleaning in an ultrasonic cleaner so will let you know how I get on as well (after sorting out another quad)

Posted

Yes That’s great.  Just take your time and make sure you do a thorough job.   I like to use a cheap white pilllow case on my work bench before I get into one. It helps to see any parts as well as the dirt that comes out.  I buy the cheap ones a two pack for $2 bucks at them cheap stores like odd lot or something.   

I also like to use a can of compressed air to blow everything out.  Staples or any office supply place has them.   

E013500D-57C7-4A84-ACF6-4D58DE774AA2.jpeg

Posted

Check the charging system. At idle you should see no more than 14.5 volts. Typically the voltage should read about 14.5 volts at 2500 rpm or so, lower at idle. An over charge condition can seem like carburetor issues sometimes. Rule this out first, it will save lots of head scratching. If you don't have a volt meter just unplug the voltage regulator and see if your issues go away,quick and free to check. 

Posted

Thank you so much for all of the info, the document on the carb breakdown has my exact one included, so thank you!  And the post regarding voltage is interesting...mainly because, my battery is dead, an I am starting it with and have my charger connected to it until the battery is replaced.  Surely is is getting a higher voltage...i will check it out.

 

Posted

So, verified that all parts are in the carb correctly, cleaned, and reassemble/installed.  Fired it up again with the same chugging sound...smoothes out a little at idle.  I did remove the charger once started, but same result both ways.  I will try to attach a video of the sound.

Posted

Just put a fresh plug in, no change.  I am guessing that the adjustments are fine because it was running good then this issue came up when I was riding it.  I do recall it happening, then it ran fine...then reverted back, and hasn't been the same since.

Posted

So, going back through the things I need again to make her run...spark-good, fuel-good...but decided to check it again... bingo!  At idle, the fuel pump works fine (almost seems like too much fuel), but when given throttle, the fuel flow stops.  Vacuum line going to pump is good, and the diaphragm in the carb looked good...so now where???

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By AnthonyT
      In search of my first ATV? What are good older 4x4 models?
    • By 1998Zuki250
      Looking to see if anyone has any input on ATV Tires? 1998 Suzuki quadrunner LTF250
    • By Rich1028
      I Crashed My Quad
      Well the Way I Ride, some of you knew it was Inevitable.
      Below are Three Videos.
      First one is Slow Motion of How it Happens.
      Second one is Normal Speed, and what happens after the Accident.
      Third one Follows more of what happens after .

      I Was Riding By Myself. I was going through a Mud HOLE Either there was a log or a rock, or A Dip but just as I was almost through it, Machine, Rolled over on my right side, as soon as I contacted the ground, I Heard A SNAP! I got up, flipped the Quad back over. I had the wind knocked out of me.

      5 broken Ribs
      1 Punctured Lung
      1 Broken Collar Bone
      2023 Quad Riding Season is Over for ME!
       
       
       
    • By Ajmboy
      So we are almost a month into winter and I've been so busy working on my house that up until today, I didn't realize that we just haven;t gotten any real snow yet to warrant putting the plow on my grizzly. So that got me thinking, what are the latest plows out there and what ATV plows are the best? I've got 2 snow plows for my grizzly, a quadboss pile driver atv plow set up and a snowsport ATV plow. They are both a bit dated now and I tend to stick with the snowsport due to ease of use and I just like it so much. So if you have a plow on your ATV, please let us know what it is and post a picture with your atv/plow would be awesome. Would also like to know what you like and dislike about it.
      This is back a while when I did a write up on these 2 plows.... in 2009 I got the snowsport and in 2012 I got the quadboss.
       
    • By Panupong Pradchaphet
      I have a Sportsman 450 HO and almost killed my self when loading it on my truck with ramps.  It rolled off the top of the ramps and tailgate and nearly landed on me.  I now want to winch the ATV in to the truck.  My question is are the front side bed tiedowns in my 2011 RAM strong enough to winch to without distorting the hooks or sides of the bed?
×
×
  • Create New...