Quantcast
Jump to content

Recommended Posts

Posted

i have a drx 90 air cooled and when my son takes off it goes fast and then when he lets off the gas and presses again it bogs down really bad. we tried changing jets going up and down and a few other things but nothing seems to work.

Posted
i have a drx 90 air cooled and when my son takes off it goes fast and then when he lets off the gas and presses again it bogs down really bad. we tried changing jets going up and down and a few other things but nothing seems to work.

Before you Changed Jets did you do a PLUG CHOP and Read the Plug to determine you need to Screw with the jets????

How is your needle Setting????

Did this Happen all of the Sudden or has this been an ongoing Problem???

Do you have Aftermarket Pipe??

How is the Air Filter????

Fuel Filter???

Air in the tires???

When you modded the motor,,,Exactly what else did you do....In other words.....I want to know EVERYTHING you have done to the Bike....and Be Weary,,,,,You cannot JET a bike on the Internet....:huh:

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By dalton7545
      ive had an account for years.   cand dowload a manual tho   havent posted enought so here is a post
    • By pastorjeep
      Ok guys, I am a glutton for punishment! I picked up this 01 2wd Rancher because the plastics looked good on the marketplace. It has been sitting in the guys back yard for 10 years. The original engine blew and they swapped in an electric shift 4x4 engine. 😒The engine is locked up and was full of water. The wiring is hacked where they tried to get it to run and the rear end needs new swingarm bearings where they left it laying on the ground in the woods for 10 years. Has anyone here ever did the engine swap? First thing is to straighten out the wiring and get the engine free to see if I can get it to crank over. I have swingarm bearings ordered and a new ignition switch. So hopefully I can at least roll it around soon. 🤣





    • By bigbell
      Does any know what the stock jets are in the twin peaks?
      I bought the bike with a pipe on it and want to go back to stock setup.
       
    • By Does_This_Look_Bent?
      Hey everyone, I just replaced the carp on my 98 Kodiak 400 with PN#4SH-14101-00-00. It starts and idles perfect, but once it’s good and warmed up, it bogs out at 3/4 throttle or more… it sounds like it’s bouncing off a rev limiter haha… I tried the air fuel screw, all the way in and out 2-1/2, and it made it a touch better… tried 2 turns and no different. Am I missing something?
    • By DaveswMN
      Pulled my '86 Moto4 out of shed where it sat for 20 years. I knew it smoked. checked it over a little put in gas and it fired right up!! 
      Drove about 100 yards, ran about half throttle wouldn't idle.  Put on somenew parts, jug/piston and rings, carb and valve seals.
      'went together ok, tuned it over by hand about 6 revs whick went well. Hit the starter it fired for about 6 revs and quit. tried it again fired once and then th sound of something slipping like maybe chain slipping over spoket.
      Took cover off to watch cam sproket, hit starter again, heard same noise and the cam sproket was not turning but jumping a bit. Chain was still tight. You will probably tell me I need to split the lower case but hoping there mightbe something else.
      I don't fully understand the chain tightener, the plunger only moves about 1/4 inch, should it move much more than that when off the motor and compressing it by hand?
      Thanks for any thoughts.
×
×
  • Create New...