Quantcast
Jump to content

Recommended Posts

Posted

Hey everyone im new here, i have a problem with my 2001 suzuki quadrunner 500. When i start the bike up it sounds fine but a few seconds later the idle speed just keeps rising to where you cant put it in gear, and if im lucky it will climb down to where i can put it in gear but when i press the gas it immediately want to die. Please help me!

Posted

Check and see the choke, it may be stuck.  Double check that and the cable but look good because sometimes it’s the choke connector inside the carburetor. 

If that’s all clear it’s possible that the carburetor needs an adjustment. But you have to figure out why because if it was running good and just started acting up then you have to find out what.  So  if the bike was fine before then something changed that.  Maybe a piece of debris/dirt got into the carburetor somehow, maybe form dirt inside the tank, bad gas who knows. 

Also look at the air intake and make sure filters are all good and nothing got sucked into the carburetor like a piece of the air filter if it was crumbling. 

I would start there. 

Posted

It did this when i got it but the starter went bad and had to wait for it to come in the mail, i got the bike a week and a half ago. I will check the choke and filter tomorrow, thank you very much

  • Like 1
Posted

Check  also  for a weak return  spring on the  main  jet needle diaphragm allowing the  carb to  creep  open  above idle ,  and make sure there is no air leak between the  cab and intake . There could be a partially  plugged  jet making the  carb run  lean. That will  make it rev  high at  idle  and die  when you open the throttle . Before digging deeper ,  check the idle air  adjustment.  Most  carbs  are set from about  3/4  to  1  1/2  turns out from gently  seated. Try turning yours in or  out about a 1/4  turn  at a time to  find the best  spot   for idle and no stall. It sounds like it is  burning  lean right now

  • Like 1
  • 3 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By kawasig
      Hello All
      I'm kinda new to ATVs. I just bought a 1987 Suzuki quad runner 230 Dual Range. I'm having a problem finding info on it. It's very clean, only 2.800 miles. The front wheels are only 30 in.center to center. I was thinking about adding wheel spacers to give it more stability. I realize the added stress on ball joints and bearings. I'm wondering if there are any other concerns? Any input is greatly appreciated!
    • By Tinkeringreg
      Hi my name is Greg and I just acquired a free 2000 yamaha kodiac 400 4x4 with the ultramatic transmission that does not run. I plan to get it going and use it around my property

    • By Mhatayas
      What should I do about this , bad oil leak where the filter cover bolts on . Can I use some gasket maker 

    • By fwsamm
      Im aware that this relay needs a positive (+) and a negative (-) to activate the other side. The blue wire is the neutral wire so when in neutral it gets ground. The green wire is from the parking break; when you pull the break in it gets ground (-). however one of those two needs to be neutral so that the positive from kill switch can go to the starter relay. The ground from the starter relay is from the start switch. Which one (neutral or parking break) should have a positive (+) voltage?
    • By kaidella
      Bought 4 wheeler for kids. Used to run and soon as it was put in gear it died. I have put new carburater, new plug and battery. The neutral light won't come on. I replaced the solenoid, then the positive battery cable and today put new relay assembly on. Still no neutral light. Not getting any juice and I don't know why.
×
×
  • Create New...