-
Similar Forum Topics
-
By Coyote251
I'm trying to help a buddy out with his bike (he's not really on the internet or familiar with these forums) and I'll admit that I am not super familiar with the transmission and clutches in these bikes. I owned a Brute a few years ago, but never had an issue like this that I had to troubleshoot.
So basically my buddy bought a group lot of 650's to build one good bike out of. He got it all put together and has it running but when he pushes on the throttle the clutch doesn't engage till the RPM's are quite high and even when its moving it doesn't really speed up, almost seems like its in "limp mode". He's tried 2 different transmissions so I don't think that's the problem.
Is there any adjustment on the clutch engagement? Anything else I can tell him to look at? Let me know if you need anymore information if you think you can help.
-
By Rich1028
I Crashed My Quad
Well the Way I Ride, some of you knew it was Inevitable.
Below are Three Videos.
First one is Slow Motion of How it Happens.
Second one is Normal Speed, and what happens after the Accident.
Third one Follows more of what happens after .
I Was Riding By Myself. I was going through a Mud HOLE Either there was a log or a rock, or A Dip but just as I was almost through it, Machine, Rolled over on my right side, as soon as I contacted the ground, I Heard A SNAP! I got up, flipped the Quad back over. I had the wind knocked out of me.
5 broken Ribs
1 Punctured Lung
1 Broken Collar Bone
2023 Quad Riding Season is Over for ME!
-
By kawasig
Hello All
I'm kinda new to ATVs. I just bought a 1987 Suzuki quad runner 230 Dual Range. I'm having a problem finding info on it. It's very clean, only 2.800 miles. The front wheels are only 30 in.center to center. I was thinking about adding wheel spacers to give it more stability. I realize the added stress on ball joints and bearings. I'm wondering if there are any other concerns? Any input is greatly appreciated!
-
By Kaz
Troubleshooting a no spark issue, was running OK, maybe a little rich, turned it off, now no spark. I've checked/ohmed out the main key switch, the start/stop switch, neutral switch, brake switch - all good. It will crank the starter, but no spark with the starter or when I try the pull start. I've checked all fuses and diodes. Swapped battery. New plug. New coil. Swapped in a used CDI - no help. Traced, removed, cleaned, reattached all grounds. Removed things like my winch from the circuits to be sure a bad relay or something was dragging it down. When testing voltages, the orange wire going from the CDI to the ignition coil shows no/very low voltage-shouldn't it have 12V on it? Sometimes I get a very weak, intermittent glow on my spark tester, but not enough to fire the plug. I've checked continuity on just about all wires in the harness. Checked/cleaned/lubed w dielectric grease- all connections, redid a few that looked old/dirty. I've checked the stator resistances, all good, but have a stator and rectifier ordered anyway, will arrive Sunday. I verified that the rectifier has a voltage output back to charge the battery while cranking - 10.5-11V, low, but expected while starter is engaged. What else can I check as part of troubleshooting? I have a Haines service manual, but the 1999 350 4x4 seems to be an odd model, there isn't an exact electrical diagram for it, but found one for another year that has all the same number of wires and same color wires, so I've referenced that. Any hints, tips or advice would be appreciated! Thanks!
-
-
By Mhatayas
What should I do about this , bad oil leak where the filter cover bolts on . Can I use some gasket maker
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.