Quantcast
Jump to content

Recommended Posts

Posted

Well, I received stator, pick and new key switch asembly. I have great spark. Thanks to all whom responded.

NOW it Starts up with hesitation. Idles good , give a little gas it boggs down, back fires & dies instantly. Will start up after it back fires

DID I MESS WITH TIMING

Posted
24 minutes ago, Todd Trask said:

Well, I received stator, pick and new key switch asembly. I have great spark. Thanks to all whom responded.

NOW it Starts up with hesitation. Idles good , give a little gas it boggs down, back fires & dies instantly. Will start up after it back fires

DID I MESS WITH TIMING

It sounds like its running lean....what kind of carb you have? Air/Mixture screw and your idle screw,but you say it idles good,try the Air/Mixture one,but you have to warm up the engine and close it all the way, not to tight,you don't want to damage or brake it,slightly snugged,then turn it counterclockwise about 3/4 or 1  1 /4  turn then wait about one minute listen to the engine,you might have to play with that for a little until you get the adjustment you need...

Posted

It only back fires now, won't run..😩

Makes one hell of a boom..

Went to try to start to warm up,

Just a recap..

1st time I started it. I let it idle long enough to install front rack, rear fender & rack., while installing items I gave a little gas and it would still bog down . jumped on and went 50 ft before it just died. Try to start it and it back fires

Will fuel will cause a huge back fire..?

Posted

Ugh amazon carb.  No good. Replacement carbs should be oem! If you still have the oem carb then spend the money on a rebuild kit and rebuild it.   It’s not difficult and we will help you along.   If the stator and pick up coil were put in right which I’m  sure you did and no you can’t screw up the timing by doing what you did then my suspicions are the carb is the problem here.  

Posted

Amazon has it and prob better off on eBay.   Look for the oem label when buying.   It’s worth it. You will rebuild the carb and set it up the bike will run great.  Just take a look on YouTube on rebuilding if your not familiar with the work and take your time. Clean work area.  I like to use a cheap white pillow case when doing a carburetor. Makes easy work when dealing with small parts on a white surface as well as seeing what comes out of the carb dirt wise .  Any questions you have we will help.  Post pics when your not sure and you will get pointed in the right direction.   

  • Thanks 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Forum Topics

    • By ATVNetwork
      As the 2025 ATV Motocross National Championship Series (ATVMX), an AMA National Championship, got underway with back-to-back Florida AMA Pro only events, it was evident that Phoenix Racing Yamaha’s Joel Hetrick picked up where he left off last season.View the full article
    • By Tinkeringreg
      Hi my name is Greg and I just acquired a free 2000 yamaha kodiac 400 4x4 with the ultramatic transmission that does not run. I plan to get it going and use it around my property

    • By Kaz
      Troubleshooting a no spark issue, was running OK, maybe a little rich, turned it off, now no spark. I've checked/ohmed out the main key switch, the start/stop switch, neutral switch, brake switch - all good. It will crank the starter, but no spark with the starter or when I try the pull start. I've checked all fuses and diodes. Swapped battery. New plug. New coil. Swapped in a used CDI - no help. Traced, removed, cleaned, reattached all grounds. Removed things like my winch from the circuits to be sure a bad relay or something was dragging it down. When testing voltages, the orange wire going from the CDI to the ignition coil shows no/very low voltage-shouldn't it have 12V on it? Sometimes I get a very weak, intermittent glow on my spark tester, but not enough to fire the plug. I've checked continuity on just about all wires in the harness. Checked/cleaned/lubed w dielectric grease- all connections, redid a few that looked old/dirty. I've checked the stator resistances, all good, but have a stator and rectifier ordered anyway, will arrive Sunday. I verified that the rectifier has a voltage output back to charge the battery while cranking - 10.5-11V, low, but expected while starter is engaged. What else can I check as part of troubleshooting? I have a Haines service manual, but the 1999 350 4x4 seems to be an odd model, there isn't an exact electrical diagram for it, but found one for another year that has all the same number of wires and same color wires, so I've referenced that. Any hints, tips or advice would be appreciated! Thanks!
    • By Kawasakibayounospark
      any one know much about how this system works. Replaced voltage regulator cid box coil pickup coil have power to cid box none out to coil any thoughts. This is cid box number three 
    • By carkivey3
      i just picked this up. was told ran fine but overheating issues led to replacing head gasket and head. has not ran since. he is not a mechanic but helped someone else who he could not get back to finish job, got aggravated and put up for sale. i was thinking timing issues. i have 110-120psi on all 3 cylinders so i think valves are correct. dont know about distributor yet. however i have no spark. i have no power going to ignition coil. tried to follow white wire but gets lost in wire harness. does anyone have a wiring diagram? can anyone tell me what conditions have to be met before starting. motor turns over so i would think all safeties are met but you never know.
×
×
  • Create New...