-
Similar Forum Topics
-
By Tim Keiper
1st problem, Does anyone know where I can find a stock carb for my Timberwolf, I have tried two different aftermarket carbs and they both suck. The machine runs great until it gets good and warm, then it keeps stalling unless I feather the throttle. it will even stall while I'm trying to go from 1st to reverse or vise versa. I took it to a buddy of mine who is a bike mechanic for years, and he told me try to find a factory carb. When I look online from dealers it says "NOT AVAILABLE" anyone have any suggestions ?
2nd, The small tab on the rear axle for towing is to short for even pulling my small yard trailer, I can't even turn a little bit and hit hits. I tried making an extension which worked great as far as length, but it bends the tab and then the extension drags the ground. I have an idea of what to do to fix it, but wanted to see if anyone else has had this problem and see how you solved it.
-
By Rich1028
I Crashed My Quad
Well the Way I Ride, some of you knew it was Inevitable.
Below are Three Videos.
First one is Slow Motion of How it Happens.
Second one is Normal Speed, and what happens after the Accident.
Third one Follows more of what happens after .
I Was Riding By Myself. I was going through a Mud HOLE Either there was a log or a rock, or A Dip but just as I was almost through it, Machine, Rolled over on my right side, as soon as I contacted the ground, I Heard A SNAP! I got up, flipped the Quad back over. I had the wind knocked out of me.
5 broken Ribs
1 Punctured Lung
1 Broken Collar Bone
2023 Quad Riding Season is Over for ME!
-
By kawasig
Hello All
I'm kinda new to ATVs. I just bought a 1987 Suzuki quad runner 230 Dual Range. I'm having a problem finding info on it. It's very clean, only 2.800 miles. The front wheels are only 30 in.center to center. I was thinking about adding wheel spacers to give it more stability. I realize the added stress on ball joints and bearings. I'm wondering if there are any other concerns? Any input is greatly appreciated!
-
By neilroy87
I have a 1990 Bayou 220 that runs pretty well for it's age--needs a new muffler, but sounds tough. Have had to start with a pull cord since I got it, and recently started troubleshooting the start button. Finding a lot of information on this issue in the forum, but haven't been able to chase it down yet. Got a new battery, new starter solenoid, and going to replace the starter relay this week, but not convinced that's going to do the trick, since I can't get the neutral light on when turning the key on. I can start it by jumping the solenoid, but the 2 black wires to the relay do not activate the starter. Bad ground or a short somewhere? Is there a good way to just test the ground?
-
-
By beast6228
I've been trying to piece this Lakota 300 back together, slowly. It's been a rabbit hole however. I replace one thing, then it leads to replacing other things. Anyway, When I got this thing I noticed that the hose coming off the camshaft cover wasn't attached to anything, it was just hanging loose. (It's literally just a foot long hose attached to nothing) I figured since it was venting the head it would be ok and I am sure it is.
However, last night I was looking at the service manual and noticed that it mentioned that this atv has a crankcase breather tube as well. Mine does not have one, so I looked at Partzilla and looked at the parts diagram and sure enough, it's definitely supposed to have one. The problem however is, the service manual does not show how it hooks up and the parts diagram only shows the exploded view of the assembly. I just find that kind of strange, nowhere in the manual does it show how it connects. Does it have it connector, attach to a nipple? It just doesn't say and it bothers me that there is a hole there without anything attached to it. If anyone has a Bayou 300 or Lakota 300 with an intact breather vent system and could possibly take some clear photos of it or know how it connects I would be very grateful. I have searched high and low and cannot find any information on it.
Thanks
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.